unable to login to router Beetel150TC1uter beetel

May 9, 2020 at 02:12:55
Specs: Windows 8.1
I am unable to open the configuration page
of router Beetel.150TC1.
All usual addresses and user/password combinations have been tried without success. Reset also did not help.

See More: unable to login to router Beetel150TC1uter beetel

Reply ↓  Report •

#1
May 9, 2020 at 04:02:16
Not a router I’m familiar with, but I’m guessing it’s one made in/local to your country?

On the back or base of most routers there is usually the correct (default) login/password for it when manufactured. If you have reset the router to factory state, did you try that combination?

Also do you know the IP address for the router’s admin pages!


Reply ↓  Report •

#2
May 9, 2020 at 06:41:22
Are you sure the model number is correct? From what I could find, there's a 110TC1 or 450TC1, but no 150TC1. The login instructions might be on a label on the underside of the router.

It seems to be the same IP address used by most routers - 192.168.1.1
Username = admin
Password = password
Look here:
How To Find Your Beetel Routers IP Address
Information About the Beetel 110TC1 Router
Information About the Beetel 450TC1 Router


Reply ↓  Report •

#3
May 9, 2020 at 07:05:28
All usual addresses and user/password combinations have been tried without success. Reset also did not help.

If you're read the manual, or quick setup guide and followed the steps correctly and it didn't work, it's time to contact the manufacturer's support people and get their help.

It matters not how straight the gate,
How charged with punishments the scroll,
I am the master of my fate;
I am the captain of my soul.

***William Henley***

message edited by Curt R


Reply ↓  Report •

Related Solutions

#4
May 16, 2020 at 00:37:23
The correct correct model number is is Beetel 450TC1 ADSL2+Router made in China! Model is further specified as ADSL2+CPE!

Reply ↓  Report •

#5
May 16, 2020 at 00:39:01
No idea. All likely addresses have been tried. I get the response as either connection timed or access not allowed

Reply ↓  Report •

#6
May 16, 2020 at 01:30:06
Presumably you are connecting to the router via an Ethernet cable - not via Wi-Fi at this time. Having reset the router the Wi-fi is very likely disabled now (the usual default state for a new/reset router).

Reply ↓  Report •

#7
May 16, 2020 at 02:12:40
Hope to enable WiFi?

Reply ↓  Report •

#8
May 16, 2020 at 03:57:24
Until you are able to login to the router, when connecting to it with an Ethernet cable, there is no way to enable or customise etc. “anything” on the router.

If you cannot login when connected that way... then either contact the supplier of your router, or seek to acquire a new one; as it would seem the one you have is faulty?

But again, are you connecting to the router via an Ethernet (cat-5) cable; and have you tried to connect/login using at least two known good cables - to eliminate the cable being fault? Obviously I mean try with one cable, then swap it for another.


Reply ↓  Report •

#9
May 16, 2020 at 05:37:35
Thanks. Will try with another Ethernet cable.

Reply ↓  Report •

#10
May 16, 2020 at 05:49:32
And ensure the cable is securely inserted/fitted at both the router and the computer; and that you are connecting the ethernet cable into a LAN port (there are usually four of them) on the router - not a WAN port...

Reply ↓  Report •

Ask Question