Please Help me

Intel D945gclf motherboard cpu bundle
October 2, 2009 at 06:36:51
Specs: Microsoft Windows XP Professional, CPUs/Overclocking
I have an old system having processor code name:- Conroe-L/Package:-Socket 775 LGA/Core Stepping A1/Technology:-65 nm/Core Speed:-1600.1 MHz (8.0 x 200.0 MHz)/Bus speed:-800.0 MHz/Stock frequency :-1600 MHz/Instructions sets :-MMX, SSE, SSE2, SSE3, SSSE3, EM64T..........and Chipset contains Northbridge:-Intel i945G/GZ rev. A2/Southbridge Intel 82801GB (ICH7/R) rev. A1/Memory TypeDDR2/Memory Size :-512 MBytes/Memory Frequency:-266.7 MHz (3:4)/CAS# 5.0/RAS# to CAS# 5/RAS# Precharge 5/Cycle Time (tRAS):-12/Bank Cycle Time (tRC):-1

My problem is that my system's CPU respond too slow on any instruction and always shows CPU uses 100%....

How can I Get Rid of this Problem.

Any One can help me, Please!

Sdbnathan


See More: Please Help me

Report •


#1
October 2, 2009 at 13:22:14
See taskman and perfmon for more detailed information.

Playing to the angels
Les Paul (1915-2009)


Report •

#2
October 2, 2009 at 22:17:48
You haven't provided enough information.

Provide all the details you can.

Was this same cpu working on this same mboard fine previously?

Have you just re-loaded Windows from a regular CD and it's only been slower since then?

How full is the C partition on this computer? What's it's size and how much free space is left?
If doesn't have enough free space on it Windows will run much slower on any computer.

The model of the mboard would be very useful to us.

Apparently it's NOT an Intel D945gclf mboard because that model has a soldered in Atom processor 230 with a 533 MHz system bus
Atom Cpus - none are 65nm or 800 mhz bus
http://processorfinder.intel.com/Li...


E.g. if the mboard made by Intel, it has an AA number on it.

E.g. if the AA number is D67193-xxx , it's an Intel D945GCL mboard, and the minimum bios version that supports your cpu properly is 32, which is NOT the first version possible - it's the second last version possible.

If it's not an Intel made mboard, the model is usually printed in obvious larger characters on the surface of the mboard, often between the slots.
........

"Conroe-L/Package:-Socket 775 LGA/Core Stepping A1/Technology:-65 nm/Core Speed:-1600.1 MHz (8.0 x 200.0 MHz)/Bus speed:-800.0 MHz/Stock frequency :-1600 MHz"

Conroe-L

http://en.wikipedia.org/wiki/Celeron

The Conroe-L Celeron is a single-core processor built on the Intel Core microarchitecture and is thus clocked much lower than the Cedar Mill Celerons, but still outperforms them. It is based on the 65 nm Conroe-L core,[25] and uses a 400-series model number sequence.[26] The FSB was increased to 800 MT/s from 533 MT/s in this generation, and the TDP was decreased from 65 W to 35 W. As is traditional with Celerons, it does not have Intel VT-x instruction support or SpeedStep (although Enhanced Halt State is enabled, allowing the Celerons to lower the multiplier to 6× and decrease core voltage while idle). All Conroe-L models are single-core processors for the value segment of the market, much like the AMD K8-based Sempron. The product line was launched on June 5, 2007.[27]

This is the only possible cpu it could be:
Intel Celeron 420 Conroe-L 1.6GHz 512KB L2 Cache LGA 775 35W Single-Core Processor
http://www.newegg.com/Product/Produ...

http://processorfinder.intel.com/de...
Processor 420 - 35w

Found 41 (mboard model revisions; Intel made) Compatible Board(s) for Processor "420"
http://processormatch.intel.com/COM...

"Chipset contains Northbridge:-Intel i945G/GZ rev. A2/Southbridge Intel 82801GB (ICH7/R) "

Only the Intel D945GCL mboard series, of the Intel made mboards, supports this cpu and has i945G (no i945GZ chipsets listed in the above list).

There are other mboards not made by Intel that support this cpu.


Report •

#3
October 3, 2009 at 02:22:13
Thanks All of You for Your sugestion.
As per my information This same CPU was
working on the same motherBoard fine previously.
Actually since I noticed this problem I formatted the system
4-5 times but no effect Found.
About the C Partition,Total capacity of This partition is 78 GB and Only 13 GB occupied.

This MB is manufactred by Simmtronics and based on Intel Chipset
i945G..
It is that which information I can give u all..
Try to find out resolution.

Thanks Again.

Sdbnathan


Report •

Related Solutions

#4
October 3, 2009 at 09:37:05
"This same CPU was
working on the same motherBoard fine previously."

OK, then the mboard's bios is probably already able to recognize the cpu type properly.

"Actually since I noticed this problem I formatted the system
4-5 times but no effect Found."

It should have been obvious once you had formatted it once that you hadn't figured out what your problem was.

"About the C Partition,Total capacity of This partition is 78 GB and Only 13 GB occupied."

OK, then your C partition is not too full - that's good, and is not a possible cause of your problem.

"This MB is manufactred by Simmtronics and based on Intel Chipset i945G.."

"If it's not an Intel made mboard, the model is usually printed in obvious larger characters on the surface of the mboard, often between the slots. "

Did you look for that?
If you don't see that, look for stuck on labels that might have the mboard model printed on them. The one for the mboard itself often also has a bar code printed on it. Sometimes the label with the model printed on it is on the top of the parallel port, when your mboard has one.

http://simmtronics.com/

http://simmtronics.com/motherboard.php
I clicked on Archive

These are the only i945G mboards they list - i945GC chipset models.
I suspect your mboard is the first one, unless yours is older and they have no support for it.

SIMM-INT 945GC-P
http://simmtronics.com/simm-int-945...

SIMM-INT 945GC-ML
http://simmtronics.com/simm-int-945...

SIMM-INT 945GC-WP
http://simmtronics.com/simm-int-945...

I see in all three cases, they do not list drivers for the 945 series main chipset. Sometimes mboard makers omit listing those drivers because there may be newer main chipset drivers on the maker of the main chipset's web site, and they don't want to have to update their main chipset drivers download.

You MUST install the main chipset drivers in order for the operating system to have all the proper info about your mboard, and for it to be able to properly support your cpu, and for it to be able to run your drives at their rated max speed.
E.g. Your mboard has USB 2.0 controllers. All USB 2.0 controllers also have USB 1.1 support - support for USB 1.x is always installed when you install a Windows operating system, Win 98 and above, but the support for USB 2.0 controllers is NOT installed in the operating system until AFTER the main chipset drivers have been installed.

After Windows Setup has finished, you MUST install the drivers for the components on your mboard, especially the main chipset drivers.

The CD that came with your mboard probably has all the necessary drivers, including the main chipset drivers.

However, if you have been going to the Simmtronics web site and loading only the drivers listed for your mboard there, they DO NOT list the main chipset drivers.

In that case, or in any case if you want to load the latest available main chipset drivers, go here:
http://downloadcenter.intel.com/Sea...

You MUST download and install this
INF Update Utility - Primarily for Intel® 5, 4, 3, 900 Series Chipsets
http://downloadcenter.intel.com/Det...

Optional - the latest onboard video drivers
Intel® Graphics Media Accelerator Driver for Windows* XP (exe)
http://downloadcenter.intel.com/Det...

If you have already installed video drivers, un-install any listings in Control Panel - Add/Remove Programs for the onboard video BEFORE installing the video drivers software installation.
........

If that doesn't help, go into your mboard's bios Setup and load bios Defaults, or, better still, Optimized defaults if that's listed, Save settings.

The Simmtronics web site has no mboard manuals you can download; therefore, I don't know which key you must press to get into the bios Setup.
Often that's displayed on your screen while booting.
If you don't see that, try pressing Del, or F1, or F2, repeatedly while booting, starting early in the boot - e.g. right after the mboard beeps once,
or - if your mboard came with a printed manual, and/or a mboard manual that's a *.pdf or Word (*.doc) document that's on the CD that came with it, look at that to find out which key you press to get into the bios Setup - that's usually stated at the beginning of the descriptions of the bios Setup settings


Report •


Ask Question