I have problem of hasp driver.

November 23, 2010 at 10:41:28
Specs: Windows XP, 2.80GHZ/1.00GB
WHEN I OPEN ONE OF MY SOFTWARE THEN IT GIVE THE ERROR OF HASP(HASP DEVICE DOES NOT INSTALLED ON UR COMPUTER).SO HOW SHOULD I OVERCOME THIS PROBLEM.HOW CAN I INSTALLED ON MY COMPUTER .PLZ ANY ONE REPLY

See More: I have problem of hasp driver.

Report •

#1
November 23, 2010 at 11:29:42
Typing a post on the internet in all CAPITAL letters is considered to be the same as if you were SHOUTING, and very rude !
.......

Tell us the make and model of your brand name system, or if you have a generic desktop system, the make and model of the mboard.

The specific model of a brand name system is shown on a label on the outside of the case somewhere, or it can often be determined by going to the brand name's web site and loading a program they have available.
For Dell computers, they have a Service Tag number - the specific model can be determined by using that on their site, or can often be determined there automatically by you downloading some software. The Service Tag number should be on a label on the outside of the case, probably on the bottom on a laptop, on the back on a desktop, and is often also shown in the bios Setup.

The model, sometimes the make, of a mboard in a generic desktop system is usually printed on the mboard's surface in obvious larger characters, often between the slots.

The model is often also displayed on a logo (graphical) screen early in the boot, but it's often not as specific as the specific model number.
......

Have you installed Windows from scratch on your computer, then you got this message ?


Report •

#2
November 23, 2010 at 11:38:10
Do you own software that uses a hardware USB lock? If so, that is what the message is about. You need to have the software for the hasp device installed AND the hasp device connected.

This allows you to use the program on more than one device.

If you have downloaded a program that requires a hardware lock and you don't have it then you are out of luck.


Report •

#3
November 24, 2010 at 03:02:14
I TRANSFERRED SOME TRACKS FROM REAL PLAYER TO USB.WHEN TRANSFERRED COMPLETE.I OPEN ONE OF MY SOFTWARE THIS ERROR OCCURED

" HASP DRIVER IS NOT INSTALLED ON YOUR COMPUTER.CLICK ON OK TO PROCEED WITH INSTALLATION....:

WHEN I CLICK OK COMPUTER SAYS "HASP DEVICE DRIVER ERROR"

AFTER SOME TIME WHEN I TURN ON MY COMPUTER THERE ARE SOME SOUNDS HEARING FROM CPU.IS THERE RELATIONSHIP B/W HASP DEVICE DRIVER ERROR AND THE SOUND WHICH I HEARED AFTER TURN ON CPU.

PLZ HELP ME....................................................
IS THERE SOLUTION OF THIS PROBLEM?
I SHALLBE VERY THANKFUL TO U IF U SOLVE MY THIS PROBLEM
WTNG FOR UR REPLY


Report •

Related Solutions

#4
November 24, 2010 at 04:19:08
Do you understand that when you type in capital letters you are being rude. So stop it.

Is this a used computer?

Do you have any Computer Aided Drawing programs installed?


Report •

#5
November 24, 2010 at 05:13:25

Do you have any Computer Aided Drawing programs installed?
how can i check are this programe installed on my computer or not?

yes this is used computer? i personally used it/how can i solve this problem
kindly give me short solution of this problem
MUHAMMAD AWAIS


Report •

#6
November 24, 2010 at 05:42:49
If no program that requires a Hasp hardware lock is installed or ever was, then I don't know why that message would appear.

Look in Windows Device Manager for a Hasp device. May be in the USB section. Disable the device and the message should disappear.


Report •

#7
November 24, 2010 at 10:56:14
how can i recognized in USB section
in USB section i have these things

1. Intel(R) 82801EB USB Universal Host Controller -24D2

2. Intel(R) 82801EB USB Universal Host Controller-24D4

3. Intel(R) 82801EB USB Universal Host Controller-24D7

4. Intel(R) 82801EB USB Universal Host Controller-24DE

5. Intel(R) 82801EB USB2 Enhanced Host Controller-24DD

6. USB ROOT HUB

Usb Root Hub repeated 5 times
so which USB port should be disabled
REPLY


Report •

#8
November 24, 2010 at 11:47:04
Tell us the make and model of your brand name system, or if you have a generic desktop system, the make and model of the mboard. (see response 1 above).

Have you installed Windows from scratch on your computer, then you got this message ?
If so, then the HASP device problem may be solved by you loading the proper drivers and software for your brand name model.

When did you first get this HASP device error message ? What did you do just before that ?
.......

None of those entries indicate you have a HASP device.

FYI
Your mboard has one USB 2.0 controller.
All USB 2.0 controllers have USB 1.1 controller support too.
The USB 1.1 controller support is indicated by the four Intel(R) 82801EB USB Universal Host Controller entries
The USB 2.0 controller support is indicated by the Intel(R) 82801EB USB2 Enhanced Host Controller-24DD entry.
Four of the Root Hubs are for USB 1.1 support - usually two USB ports are available per USB 1.1 Root Hub.
One of the Root Hubs is for USB 2.0 support - it has a lot more than two USB ports available.

The USB 1.x (1.0 and 1.1) support is built into XP (Win 95 OSR2 or greater and Win 98 and above), and XP installs it automatically.
The USB 2.0 support is built into XP if it has SP1 or later updates installed in it, but XP doesn't actually install the USB 2.0 support until AFTER the main chipset drivers for the mboard have been installed - in your case, those main chipset drivers have been installed.

You can find out how many USB ports a Root Hub has by RIGHT clicking on it , choose Properties (or by double clicking on it), and clicking on the Power tab. If a device is plugged into one or more of the USB ports for it, the device(s) will be listed, and the current it(they) draw(s) will be stated beside it(them). Total ports for the Root Hub = ports available (if no ports are being used) , or (if some ports are being used) ports available plus one port for each device listed, or (if all ports are being used), one port for each device listed.
If the device is designed to work better with USB 2.0 support, it will be listed only in the Root Hub - Power listings for the USB 2.0 controller support.
If the device doesn't need USB 2.0 support, it will be listed in one of the 4 Root Hub - Power listings for USB 1.1 support.

The total number of USB 2.0 ports = the total number of USB 1.1 ports. They are the same ports, used for both USB 1.x and 2.0, the same number as the total number of physical USB ports built into the mboard plus the total number of USB ports available by connecting to USB headers on the mboard, whether you have something connected to those headers or not.



Report •

#9
November 24, 2010 at 13:38:58
Do not remove any of those listings.

You have not made it clear if there ever was a hasp device in use on that computer.

If you are not the original owner of the computer someone else may have used a hasp hardware lock for some expensive program. These devices look like a flash drive. If the device and the software were removed the driver for the hasp device may still be installed.

Look in Control Panel> Programs and features for anything that might be that hardware. Possibly Aladdin in the name. Should have been a USB device.


Report •

#10
November 24, 2010 at 14:02:50
If you're SURE you don't have a HASP device, then search the web, e.g.

http://ca.search.yahoo.com/search;_...


Report •

Ask Question