Summary: Hello Guys, I just uninstalled a Canon Driver and wanted to istall a HP Deskjet 660C on a Win 3.11 System. But when attemping to install the second Di...
Summary: I have an old 486 and would like to install win95 on it.it has no cd rom but i have 95 upgrade on floppies. it does not have win3.1 on it and the upgr...
Summary: To Santa Date: 6/5/2007 Update: As instructed:Formatted drive. Installed Dos 3.22. Ran memmaker. Installed WFW311. Then: a. From RUN option in File Mg...
Summary: CDs are read only, so of course the disc is "full" no matter what. Check your burning software documentation, creating bootable ISOs from a floppy dis...
Summary: I have 2 different approaches: One is a complete set of files needed both running and INSTALLING Windows (which is longer). The other approach is only...
Summary: I'm trying to run the install of a spanish version of office, since it's already installed, on an english version of wfwg. I don't think that could b...
Summary: I have a Yamaha sound card and have been to thier website and downloaded the drivers for it. I tried to run the install.exe file from the dos prompt ...
Summary: OK. I installed it, but Im still getting on startup that the networking driver is not running. for network setup, I have: Only windows network running...
Summary: One reason Windows 3.1 is incompatible with MS-DOS 4.0 is because 4.0 can only access drives to 540 Megabytes. You can run windows without D...
Summary: My friends computer, a 486DX Compaq, running Windows 3.1 and Lantastic 6, was working fine. No changes were made to the machine (i.e. no installs or r...
Summary: Transfer all the files from the backup directory to a directory on the old PC, and just run the install from that folder...windows doesn't have a prob...
Summary: Card services is installed under DOS. It loads drivers in the DOS bootup file, config.sys The modem driver runs under Windows, not DOS. Try running y...
Summary: I had the same difficulty and discovered that reloading windows on top of a corrupted windows already in your system is going to just cause more probl...
Summary: Hi melvis: You should be able to install second drive as a slave drive, you need to make sure that it's dip pin is set for slave not master. Then conn...
Summary: Hi Moni First off--this is old post---BUTGOODINFOHERE do you have MS-DOS 5.0----win3.1 win98 upgrade--if so do this--- Get diskmanager for your hdd(((...
Summary: To All, I have run across an interesting problem that I need some help with. I think that I am dealing with a Virus, but am not 100% certain. Any hel...
Summary: Found this while surfing: http://www.faqs.org/faqs/windows/win95/faq/part02/section-6.html 2.6. How do I install old DOS and Windows 3.1 on a Win95 sy...
Summary: I see... Then you can try to prepare a FAT16 partition (create , format). Install DOS. Then copy all the files you have on floppies to a temp director...
Summary: go to dos try the undelete command. If thats no good your pretty well stuffed. You will have to find the original software that came with the soundca...
Summary: OK this a rather lengthy post, perhaps a bit imprecise, and it may require many different answers. Thanks in advance for helping me out. OK, basics: m...
Summary: Hi I was trying to install a 24X Wearnes CDS-2420 hard drive. After running the install disk in DOS 5.0, during boot-up, error message said driver mi...
Summary: Well here is the deal, I came across some old software, well i wanted to have a little trip down memory lane so what i did was i installed it on my co...
Summary: Backups are always a good idea, so you are certainly more prepared than a lot of people (the majority, actually.) This was always the beauty of Window...
Summary: Dear Rhonda It sounds like you executed the downloaded file on a floppy disk ( good move ). At the A:\ prompt, did you then type setup.exe from that f...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
