Summary: After some early errors in prime, I have since increased my vcore to 1.7 to obtain a 250 FSB on my p4 2.8/asus p4p800 deluxe, and the vdimm to 1.75. ...
Summary: Hello everyone, thanks for the great advice. Heres what I have done: I ran prime 95 and it ran fine, my cpu went upto 75c. But it did not crash, which...
Summary: if you had the amount of sh*t ive had with that AsRock you would probably prefer running a p75, the asrock is a budget board and a piece of crap, no g...
Summary: Your board is limited to Vdimm 2.9V, unless you Vdimm mod it, that's the max you can go and I think that's plenty juice (maybe too much for your ram. ...
Summary: In the event that your multiplier is locked, all you can do is change the FSB. You can usually tell your multi is locked if you try to change it and i...
Summary: I actually bumped the FSB 1:1 all the way up to 235 with SPD defined 3-4-4-10 (HyperX 4000), the temps were great, 42 idle, 47 full load, but Prime 95...
Summary: A Barton being overclocked to 2.5GHz is quite a leap, don't you think? Have you checked the stability of the system using programs such as Prime 95 or...
Summary: Since I don't know your mobo, I'm going to just try to give a crude guideline, other people may give you detailed "how-to's". First you need to lock ...
Summary: A K6-2+ 450 ACZ stepping will do 550 at around 2.2 (default is 2.0) voltage. But you will pay as much or more than you would for an Athlon 800 or so (...
Summary: Not sure how to ask this but do I want to keep my FSB around 1000? If yes, then what do I need to tweek to keep it low as I OC? My last attempted Twe...
Summary: Hi, i have overclocked my AMD Sempron 3100 to 2.142GHz(using 1.4volts) using a FSb of 238mhz and the ram clock at 195mhz. When i try to go past a fsb ...
Summary: I have a msi k8n neo2 plat and a 3000+winchester runs 2.8 gig 100% stable 35c 1.4v idle 42c 1.45v after running prime 95 for 24 hours can boot at 2.9...
Summary: I highly recommend you not jump straight to 200MHz bus and 2.2GHz clock. That's relatively unsafe. Start raising the bus speed by 5MHz increments. ...
Summary: Jam, Can't get it to boot up at any setting above 200X2 (400FSB) with new PC4000 ram. It won't post period. Raised voltage to 1.75. Still no help. Cur...
Summary: I have had my proccesor over clocked to 2.565ghz according to CPU-Z. I can run games for hours with no problem, same with applications., I also ran p...
Summary: Hi to all Ok, I don't know where to start... Is it possible that an overclocked system (Barton 2600 516ddr333 Asus A7V8X-X) Run at 196 11.5x fsb392 2....
Summary: Oops...sorry about the Dell part..I am not all here today! Intel I'm sure doesn't like the idea of squeezing more speed out of a chip as opposed to bu...
Summary: don't just jump right to your goal...take your fsb up slowly and test the stability..testing means take it through it's paces through programs like si...
Summary: the same results i will overclock as soon as i get it to boot but when i had my 512 p3200 i had them set to stock cuz it wouldnt be stable under prim...
Summary: Well unlocked 2500+ are as common as rocking horse dung...so you've not done bad. Its good to run your memeory in sinc, so I'd guess that ddr400 will ...
Summary: FYI The Processor is "unlocked" if you can change the multiplier which will increase processor speeds OR you can increase the FSB to increase processo...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
