Summary: I deleted the non-dos partition (XP gone bad was in it) and created a primary Dos partition using Fdisk hoping to install Win98. But when I reboot to ...
Summary: Hi guys. I have problems getting the cdrom to work in dos mode under Win95. The error mess I keep getting is "No drives found, aborting installation. ...
Summary: I just installed a SOYO IDE Raid MB in my computer. I reused the old HD with win98 on it. Everything boots fine. So I installed 2 IBM 6.5 Gig DeskS...
Summary: I got a computer supplused for storage at my work. When I started it up it wants a command interpretor and has no drives c:\, a:\ or d:\. It wont boot...
Summary: I ran FDISK on an old machine with w95 and now I want to install w98. After I boot up with the startup disk I get the message "no drives found, aborti...
Summary: I have a Packard Bell 233 MHz Pentium Processor with MMX Technology, I installed a Western Digital 40 gig hard drive and also added a SIIG ultra ATA/1...
Summary: I am using a Dell Latitude L400 that has no CD or Floppy drive. I wish to get Windows ME off here, first re-partition the drive, and then install Win...
Summary: I pulled the old PC out of the closet the other day to set up for the kids. It booted to Windows98 just fine the first time I started it, but the CD ...
Summary: I am trying to install a second harddrive in my system. My master (and original) is a Fujitsu 3.5gig and hooked up as the slave is a Fujitsu (new dri...
Summary: Drives "E" and "f" used to be my DVDROM and my CDRW drives respectively. Today I go to use my DVD drive and Windows does not respond. I see that the...
Summary: i have an old computer with windows 3.1. the boot is either boot from floppy or hard drive. since it has no way of booting from cd, is it possible to ...
Summary: Actually Mavis you only need a Boot EEPROM on the mobo with a basic O/S , does not have to be **-DOS, and no drives are needed whatsoever.. ...
Summary: I have two hard drives on my system. I took the slave out and replaced it with another hard drive, (jumper set for slave). The bios detected both d...
Summary: The tape drive is listed in the device manager but no drive letter has been assigned so I can't see what is on the tape. Also, is there a way to "view...
Summary: I've been trying to fix up an old 133 for a friend, new HDD and more memory with numerous problems recognising the drive. Now I'm constantly getting ...
Summary: I have made a new partition on my HD and installed Windows ME on it.After the install of Windows ME my old partition (Windows 98SE) lost its driver le...
Summary: FAT16 & FAT32 have not one thing to do with the floppy drive. No conflicts or double entries in device manager? No drives in 'MS-DOS compatability m...
Summary: No references at all in Device Manager, and nothing obvious in BIOS (don't know what I'm doing though!) Using floppy didn't work - tried driver, but f...
Summary: yea tried that but says installation is aborted and no drives can be found . so in dos i done C:>DIR\S MSCDEX.EXE, and says volume in drive c has no l...
Summary: Does anyone know how to get a computer or OS to detect a HD? I've tried using CMOS and I think the computer knows its there but when I go to Windows, ...
Summary: On a working system I upgraded a 2gMaxtolHDD to a 20gMaxtolHDD. Using Maxtol s/w the partitioning and format went ok.Restarted with system diskette. T...
Summary: Yep, DAVE and ham are exactly tight. But keep in mind that the 20GB WAS drive D but there are no drive letters until the OS boots and assigns them. DO...
Summary: I think this is the right spot to post, so here it goes: I'm trying to use a SD (SanDisk 1.0GB) through a card reader (SanDisk ImageMate 12 in 1) afte...
Summary: I have added a 2nd hard drive. Both cables are firmly seated. I set the second hard drive to auto in the bios. The jumper is primary slave. When I boo...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
