Summary: I installed windows 3.11 for workgroups in a 386 based system, 4 Mb ram, 47 mb HD (Seagate) and dm9008f network card. I made the installation on a pre...
Summary: Yeah, what Dan said ;-) That's a pretty empty config.sys - and it doesn't do much good *just* to load himem.sys device=c:\dos\himem.sys device=c:\dos\...
Summary: My computer was having trouble booting up so I used the boot up disk to start over. Well, as I was in the DOS menu reconfiguring everything, I select...
Summary: James does not say it. You write a Config.Sys File with a normal text editor such as Edit.exe supplied with MS-DOS, Write each line of text as shown, ...
Summary: Hi Zizo: These files are needed to boot system, they were originaly created when istalling DOS. You should be able to find other autoexec & config fil...
Summary: Hi, Im using win98 with fat32, when I open msconfig my config.sys file is empty, also when i type emm386 at the dos prompt it says emm386 driver not i...
Summary: 1)Boot up with a boot disk, 2)copy your autoexec.bat and config.sys files to a temp directory. 3) Since you have done some updating, some program or ...
Summary: Hi there, I've recently resurected my old T2130cs laptop with a clean install of DR-DOS and Win3.1 and with alot of reading from this forum! So happy ...
Summary: Excuse, my english is bad... I need: autoexec.bat, config.sys for 80286 with win 3.1 help me, please! (no se puede ejecutar windows en el modo 38...
Summary: I accidently wiped my hard drive so i installed win.3.1 when i type win this is the message i get: Missing HIMEM.SYS; Make sure the file is in your Wi...
Summary: my computer is running win3.1 when it starts , the OS will go through config.sys there is a line such as device = c:\...\..\ himem.sys it shows ...
Summary: I was once told that there is a dos based utility that allows you to add device drivers after config.sys and autoexec.bat have been processed. I would...
Summary: Hi everybody, In my 486 80 MHz 40MB RAM Windows 3.1 machine I can't connect at present with Netscape 3.0 or with MSIE50 because there appear messages ...
Summary: Esto fue hecha con el translater de Alta Vista, esperanzadamente usted puede entenderlo. Le creo dicho cuándo usted entra Windows que le está diciendo...
Summary: Hi and thanks for your help. It installed without any problems but I got an error message when i tried to start Windows: "A file that could be needed ...
Summary: I'll look for the file.This may help a little too. Config.sys DEVICE=C:\WFW\HIMEM.SYS /TESTMEM:OFF DEVICE=C:\WFW\EMM386.EXE NOEMS BUFFERS= 40 FILES=80...
Summary: This computer is on a P2P network.It has a Creative CT2810 SB sound card. On the installation instructions had to install CTCM & CTCU before sbbasic.e...
Summary: Installed WFWG 3.11 over Windows 3.1 and now crashes on boot. If I remove the line in the config.sys about the IFSHLP.SYS file everthing is then fine....
Summary: You have to clean out your root drive and sys your harddrive. Get rid of any file with a date of 7/11/95 -or better yet take'em all out so your C:\ ro...
Summary: i first installed dos 6.22 and then i installed WFWG 3.11, but when i try to load WFWG 3.11 it freases on boot. If I remove the line in the config.sys...
Summary: I'm having a bit of a problem with WFW 3.11 and the PCMCIA network card I have. It's a Realtek RTL8139(A) card, for which I found the 3.11 drivers. T...
Summary: dose anyone know how to successfully install a cdrom driver when you don't have one? is there a standard command to put into the autoexce.bat and conf...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
