Summary: Sorry for long "subject" but I have been searching message boards for two hours and can't find what I need. I have been given a CTX with DOS version ...
Summary: hello i have a computer with a blank FAT 16 partition on it which i want to install windows 95 on. i have a bootdisk and the windows 95 cdrom, and i h...
Summary: I had Windows 95 in my Computer, but I formatted the Harddisk tu clean up the system. now I want to install Windows 95 but i dont know how to start th...
Summary: I am trying to install Windows 95 on a machine that does not have a CD-ROM drive. I could easily make a bunch of floppies - but I want to do this the...
Summary: God please someone help me before I am forced to take a sledge hammer to my new computer! PLEASE! I figured out how to get to DOS on this computer w...
Summary: You need to Fdisk (partition) and format the hard drive. Take the system disk you made back to the computer you made it on and put Fdisk.Exe and...
Summary: First misstake you used doublespace. You need to format your hard drive. First you have the command.com from the english verson you need the japenese ...
Summary: I have tried to install "Windows for Workgroup 3.11" on my older computer (which is now running Windows98) and after i installs it It's not working. I...
Summary: I am fixing up an old Amstrad pc it comes with dos 4.01 when I try to install windows 3.11 I get no memory manager but with dos it say I have amstrad ...
Summary: I need to install windows 95 on to a system which has windows 3.11 and dos 6.22, but no built in CD-Rom. Is their any way that this can be done....
Summary: ok how do I install windows 95 on a notebook that has a swapable flopy/cdrom? I can boot up with the setup disk but I have to shut down to switch to t...
Summary: I have created a bootable CD from my own legit DOS 6.22 and Windows 3.11 Floppy's, I can boot and install DOS and then Boot and choose to install wind...
Summary: Even though you only have W2k and WXP upgrade CD's, you can still do a clean installation with them. All you have to do is set you CDROM as you first...
Summary: I formatted my harddisc and now I cannot get access to my cd-rom drive. I can boot the system with my win95-undo-disc, but everytime i type "E:" (my h...
Summary: Kat: First off, if you are trying to install Windows 95, I believe the minimum requirement was a "386" CPU. If you are talking Windows 3.1, it sounds ...
Summary: The problem is that MS-DOS and large drive support do not mix. Even though you FDISK with Windows 98, you must refuse large drive support and ma...
Summary: If you're using DOS 6.22 or earlier version, you'll need to install pcmcia card drivers in your c:\config.sys file and in your c:\autoexec.bat file. D...
Summary: My c: drive is compressed. so i can't install windows 95 into it. and i can't even go into windows from dos. is there a way to uncompress the c: drive...
Summary: dont know if anyone is still reading this but win 95 will not install or run on dos 6.22. the win95 cd will have dos 7.0 on it. it is not a full ver. ...
Summary: my cd rom access from dos is extremely slow, about 20 times slower than it should be literally. My computer crashed, I wiped my hd and I am trying to ...
Summary: I have MS-Dos 5.00 on 3.5disks, and I'm trying to make a bootable cdrom to install the dos os. I made a system disk with Oak cdrom drivers, it works o...
Summary: If your C primary partition is FAT 16 the MS-DOS 6.22 boot disk with CD-ROM support can be used to install Windows 95.Most people would use Windows 98...
Summary: I have win98 and dos6.22 on the same machine(intel). I am using Partition magic and it is installed on the windows partition(windows then dos). i ke...
Summary: I'm trying to install Windows 95 on an old PC that was previously an NT box. At the beginning of the Windows setup, I get the following error, ERROR ...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
