Summary: Ok, I have 2 hard drives and 2 CD drives. I have the HD on one IDE cable, and the CD drives on the other. I wanted to put them so that the cables were...
Summary: But if you do put on the HD's as primaries and CD's as slaves, I heard somewhere that since the CD's at most run at ATA33, the drives will also run at...
Summary: I currently have 2 cd drives, and the read cd's fine if the computer has started up with these cd's in the trays. The problem is, if I take a cd out a...
Summary: CD drives aren't recognized after formatting (old PBell Legend 418CD w/ 2 CD drives matsus---a CR-563-B I'm a poor boy that likes to tinker... Been ...
Summary: Is your CD Drive connected to the motherboard? Replace the CD Drive with another one if you think your CD-ROM Drive is causing you problems. Try readi...
Summary: Thanks for helping. The hard drive is on the primary ide channel and and cd drive is on the secondary, both as master, and it still does it =/. I shou...
Summary: Does the other notebook have a floppy & optical drive? Here's what you'll need to do... - Swap the HDD, then boot off a Win95 boot floppy. - Partition...
Summary: Setup: MoBo: ASUS P4B533-E (with RAID) OS: Win2000 2 HD's connected to the primary IDE channel 1 DVD-player connected to secondary IDE (Master) 1 DVD-...
Summary: Hello Thanks for the responce I just finished the project today the ata and sata have no issues being together in the same env just some other points...
Summary: I'm currently working on a friend's computer who is running a 300Watt Power supply with a Asus A7V133 Motherboard with 512MB SDRAM (2 256 chips). He ...
Summary: Hi..Have 2 20Gb HD's..used Ghost last night to clone Drive C to Drive D..now-how can i get into Drive D to run it?..is there a software program i can ...
Summary: Trios make a device (I have one) that allows three HDD to boot from. You plug all three HD's in and set them to master. You then plug the one IDE ...
Summary: Putting 2 optical and 2 SATA HD's on an ABIT IC7-G Max II Motherboard. Has 2 IDE channels that can run 2 drives each, and 4 SATA channels. BIOS is AWA...
Summary: Yes, power cables are connected, hard drives are spinning up. IDE Controllers - ? I checked Bios, ide drives set to auto. Using 1 ide channel, other h...
Summary: As you gave nearly no system specs you first need to check if there is a maximal size your mainboard and bios version can support. You can chack th...
Summary: I have been running with one master HD and one slave HD for a while now. The master is connected via Serial ATA and the slave is connected via IDE cab...
Summary: I have recently built my owm computer with a 60gb hardrive, and a 50x cdrom drive and a 32x*12x*40x rewritable drive, but when it comes to copying cd ...
Summary: The Cd Drive on My laptop dosent seem to work! The Hard drive is clean and i want win 98 on the laptop. i use the win98 bootdisk and select "with cd r...
Summary: The laptop and the hard drive will always heat up and eventually reach a stable temp when used awhile, but is it excessive? If you can check the temp ...
Summary: Hello everybody, I've install Hard Drive before(3 years ago). And now I decide to buy a new internal HD. But I forgot how to install hard drive :( Oka...
Summary: I'm not a very knowledgeable person on this, so I hope someone can help. My brother bought a used computer. It has the specs I said above, and a 10 gi...
Summary: Hello Everyone, I tried to again use my acer aspire, I had no trouble with it, when I bought a faster computer. It had not been used for months, I wen...
Summary: Ok, I've always thought that the best way to install a system with 2 hard drives and a CDRW and CDROM drive is by putting the primary hd to primary ma...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
