Summary: my lil brother went in a removed all the wires inside my computer so i went and conected them back and now when i try to start up windows i get this m...
Summary: I have 2 identical old computers - both witn Intel Pentium S 100 mhz CPU, 64mb ram, EZ-Bios, WD 8 gig hd that I have been trying to install Windows 9...
Summary: I am trying to reinstall windows 98, and I keep getting "type the name of the command interpreter". When I type in c:\windows\command.com, it repeat...
Summary: I too have "type the name of the command interpreter" I have tried all I can find, fdisk, scandisk, tried making it boot from cd-rom, floppy...I reall...
Summary: First off, the hardware: I'm on an OmniBook800CT with a 166Mhz Processor, 64 Megs RAM, and 2 Gigs HDspace. It has no built in input devices and I have...
Summary: I've ben given a computer that will not boot up. All I get is a prompt that says " Type the name of the Command Interpreter" Does any body know what i...
Summary: Trying to install WIN98 SE (which I have done before on another computer). Booted with a WIN98 SE start-up disk. Used fdisk to wipe clean, partition. ...
Summary: When l turn on our Packard Bell Pentium 100,it starts up in Dos, Windows 98 quickly starts up then shuts down. Dos is showing this message- Type the ...
Summary: I recently received a 486 66mhz DX2 that was running Win 95. I'm pretty sure it was running just fine but i wanted to start clean so I repartioned an...
Summary: Hi I'm having a little problem finishing a fresh install of windows. I was given an old Dell Dimensions XPS D300 pc. I did an fdisk and a format of t...
Summary: i've surffed for hr.s tryed every thing i saw (sys.com)rebooting and much more i think i may have more than one problem. it's a win 95 (4.26)i remove...
Summary: HELP! I tried to format my hard drive by using format c: I had a boot disk that started to work then errored out. It seems as if Windows is partiall...
Summary: when it start my computer is goes to a page that says: Type the name of the command interpreter (e.g. C:\WINDOWS\COMMAND.COM) C> my A; drive doesnt wo...
Summary: I am trying to install windows 98 second edition to my 486 computer. I have tried several things, but it always seems to come down to: "type the name ...
Summary: building new system, 677 mgz celeron processor, intel mother board, partitioned and formatted 13 gig hard drive,installed win98, when system rebooted ...
Summary: I cannot get past this message. I can't even get to the desk top. The following file is missing or corrupted. command.com Type the name of the comman...
Summary: I am putting together a system with an ASUS motherboard, 200mhz pentium CPU, 64 mb RAM, and a used 2.5 Gig Western Digital hardrive. When booting wit...
Summary: This is what my computer says now whenever i turn it on... CMOS Date/Time Not Set Run Setup Press f1 to Resume (i press f1 to resume) Searching for bo...
Summary: hello, I got a virgin hard disk, and went to install win98 1st edition on it. I can get it to attempt to start win98, but then it asks for a command i...
Summary: I'm trying to install the original software from my Sony recovery CD; it goes through the whole deal and is booting up for the first time, when bam! s...
Summary: I am having the same problem with Windows 95 that Denise posted on 9/01/03. I'm told that HIMEM.SYS and IFSHLP.SYS and SETVER.EXE are missing or corru...
Summary: My computer starts to boot to 95. As 95 is about to start the following message appears. Following File is missing or corrupted C:\windows\himem.sys C...
Summary: When I try to start my computer, the following message comes up: "Type name of command interpreter". I typed "SYS C:" then enter as was suggested in a...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
