Summary: I received a disk boot failure and it said to insert systems disk and press enter then it said to type in command interpreter can anyone tell me what ...
Summary: my lil brother went in a removed all the wires inside my computer so i went and conected them back and now when i try to start up windows i get this m...
Summary: First off, the hardware: I'm on an OmniBook800CT with a 166Mhz Processor, 64 Megs RAM, and 2 Gigs HDspace. It has no built in input devices and I have...
Summary: Trying to install WIN98 SE (which I have done before on another computer). Booted with a WIN98 SE start-up disk. Used fdisk to wipe clean, partition. ...
Summary: When l turn on our Packard Bell Pentium 100,it starts up in Dos, Windows 98 quickly starts up then shuts down. Dos is showing this message- Type the ...
Summary: Doxy, During the "Bootup", the BIOS setup looks for a Bootable Disk. [We want that to be our Hard disk]. A bootable IDE HDD is one which is properly...
Summary: Ok - your machine satisfies the minimum specs for Win98 - performance won't be great, but it should run. No, MS-DOS 622 likely would only complicate t...
Summary: I cannot get past this message. I can't even get to the desk top. The following file is missing or corrupted. command.com Type the name of the comman...
Summary: I am putting together a system with an ASUS motherboard, 200mhz pentium CPU, 64 mb RAM, and a used 2.5 Gig Western Digital hardrive. When booting wit...
Summary: I'm trying to install the original software from my Sony recovery CD; it goes through the whole deal and is booting up for the first time, when bam! s...
Summary: My computer starts to boot to 95. As 95 is about to start the following message appears. Following File is missing or corrupted C:\windows\himem.sys C...
Summary: When I try to start my computer, the following message comes up: "Type name of command interpreter". I typed "SYS C:" then enter as was suggested in a...
Summary: I put an old slave drive into my new computer and set it as the master drive (I edited CMOS and switched the jumpers). When it starts up it starts to ...
Summary: I got the same message a couple of days ago trying to install NT 4.0 on a Dell 486. When I would get to setup disk 3 I got, "type the name of the comm...
Summary: I recently had to wipe out windows and reinstall it. I get past the first phase of installing windows. After the first reboot i get a message that sa...
Summary: The following file is missing or corrupt: COMMAND.COM. Type the name of the Command Interpreter. Windows 98 and Everytime I start up the PC it keeps g...
Summary: I have an IBM system that will not boot,I keep getting the message enter correct name of command interpreter (eg, c;\command.com) A>. I have tried to ...
Summary: I have 2 identical old computers - both witn Intel Pentium S 100 mhz CPU, 64mb ram, EZ-Bios, WD 8 gig hd that I have been trying to install Windows 9...
Summary: I am trying to reinstall windows 98, and I keep getting "type the name of the command interpreter". When I type in c:\windows\command.com, it repeat...
Summary: I installed Win95 OEM Ver C then Wengier's DOS 7.10 and now I have three different command.com on my system, including the one from the \windows\opti...
Summary: I too have "type the name of the command interpreter" I have tried all I can find, fdisk, scandisk, tried making it boot from cd-rom, floppy...I reall...
Summary: I've ben given a computer that will not boot up. All I get is a prompt that says " Type the name of the Command Interpreter" Does any body know what i...
Summary: I recently received a 486 66mhz DX2 that was running Win 95. I'm pretty sure it was running just fine but i wanted to start clean so I repartioned an...
Summary: i've surffed for hr.s tryed every thing i saw (sys.com)rebooting and much more i think i may have more than one problem. it's a win 95 (4.26)i remove...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
