Summary: i have this cisco 2503 but it won't take a break sequence and drop to rommon. i am using hyperterm in windows xp. i know the password needs to be res...
Summary: We have two Cisco 2503 routers approximately 100 miles apart connected by a 64k leased line. To complicate matters further the leased line side of ...
Summary: Dear all, i have a requirement of pulling Cisco router/switch startup config to a tftp server, most of my IOS are below version 12.2 so I cannot try ...
Summary: I use a work computer from home, it connects to email through a Cisco VPN client, and I am consistently getting error message 412: the remote peer is ...
Summary: Have a Cisco 1720. To use the dial in remote access do I need a modem or can I simply connect in a standard phone line with dial tone directly into t...
Summary: I am trying to deploy several Cisco 1242 access points. I am using power injectors to power the devices, but the status light stays orange. If I plu...
Summary: Hi, I wonder if i may run a few questions past you guys. We have a Cisco 1700 at one of our sites which is supposed to be managed but due to problems...
Summary: Hi, I am new to cisco catalyst switches.I need to change hostname for one of cisco catalyst swich.How do i do that.Can some one provide me the steps ...
Summary: I currently have 5 Cisco 831 VPN setup using ah-md5-hmac esp-3des esp-md5-hmac encryption I am interested in purchasing a Cisco 1811 Broadband router....
Summary: Ok, question for all the Cisco folks. I purchased a Cisco 1417 router on ebay to replace the router provided to me by my ISP (A 2Wire Wireless GW rou...
Summary: I am trying to enable port scaning on a cisco 3560. When I do it shuts the interface down. I am running an IDS on the destination port and need to acc...
Summary: We've just finished upgrading our network infrastructure. We have upgraded our Cisco ASA to Cisco ASDM 6.1 for ASA. Our users spend a lot of time on...
Summary: Hey All, I am attempting to configure a Cisco 1841 with (1) “WIC 1DSU-T1 V2” interface for use with WAN connectivity and (2) Fast Ethernet Interfa...
Summary: - I don´t have any problem to connect using my cisco vpn client, but after 45 minutes this connection is down, why? How can I fix this problem and my...
Summary: Hi all, I need help to find out how can i access cisco 2960 switches using IE as i am not a network pro so i feel comfortable using web interface ...
Summary: how to set up two branches of banks to work in correspodance. which software will i used. please some one should help me out of this situation. i a...
Summary: The basic flow of the process is: User end(core router) > Switch (Cat6500 for distribution) > Servers. The users create telnet sessions. These users i...
Summary: I have a question about a unique configuration scenario I was hoping someone could help me with. I have an ASA5505. Eth0/7 is a member of VLAN1 and w...
Summary: I have a cisco router that likes to query (ARP) every IP address on its subnet. I don't know if it is a setting within the router or something extern...
Summary: Hi, I am just configuring Cisco AP aironet 1200 and cisco ACS for users to authenticate. This is consulting question.. Can anybody explain me. If wire...
Summary: It might be better if you setup a VPN (IPSec) on your Cisco router other then using port forwarding ,it could open holes on your network for attacks....
Summary: Hi All, I have a Cisco 1605 router that connects two networks. Each ethernet port has been configured for the networks (IP/subnet), I have enabled IP...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
