Summary: I fixed it, turns out it goes into a failsafe mode when its set too high, but, the processor fan is still dead and my processer was running at 75C whe...
Summary: kt333 chipsets keep dram timing separate from fsb. You can do what you want with the fsb and multiplier without concern for the ram. Some boards aut...
Summary: 1 - no, yes, yes. The fsb is a physical path between the cpu and the mobo northbridge chip. The mobo will detect a 100fsb cpu and set the fsb freque...
Summary: Hi, I've got a MSI KT4-V-L mobo with an XP1900 and 512mb of 2700 ram in it. It runs rock solid at 100 FSB but of course only reports the cpu at 120...
Summary: I'm running an ECS L7S7A2 motherboard with an AMD Athalon XP 2600+ with the 333 FSB. Problem is the motherboard is running it's FSB at 133, it needs ...
Summary: Question about setting the bus speed to 133 MHz (vs 100 default). I have an XP2000+ on an ECS board and PC100 RAM. I know you have to set the FSB to...
Summary: yeah i know what u mean.. I have a problem of my own with the Bios.. but anyway , reseting it is not the problem.. but configuring it seems to be... U...
Summary: ya, you can't just set the fsb from 100 to 133 just like that on duron cause the duron has a loked multiplier ==> by setting the fsb to 133 you clocke...
Summary: Hi I have a KT7-RAID with an Athlon XP 1700+ and 1Gb PC133 SDRAM...but I can't set the FSB to more than 103Mhz, so I can't run the Athlon at even its ...
Summary: Hi all hoping you can help. I've got an HP Kayak XU tower running dual xeon's. I guess it's a 3 part question. First how can I find ot if the machine...
Summary: I dont know where to start... so I'll start at the begining. I have a athlon xp 2100+/mobo combo, It boots fine with the fsb set to 100, but that set...
Summary: I cant get my PCChips M848A rev 2.1 board to run my Athlon TBird 1.4 at 133FSB. Or any other FSB except 100. I swapped my motherboard and PSU recently...
Summary: You didn't answer my question about your CPU. Chances are, your multiplier is locked...if your 1000mhz Athlon is the 100FSB version & you set the FSB ...
Summary: Depending on your motherboard and the type of cooling you have for your system, you could try the following by adjusting the Front Side Bus (FSB) cloc...
Summary: Hey YO, If the multiplier is locked (which I had asumed it was) & the CPU was intially recognized as 1.25GHz with the FSB at 100MHz, the multi is obvi...
Summary: OK, So I still haven't fixed the problem, though I've made some progress (I guess). Flashed the bios, set the FSB/DRAM ratio to 3:3, changed the memor...
Summary: It appears that you're trying to run your XP1700 at 1.7ghz...I don't know if you're deliberately trying to overclock or if you're under the impression...
Summary: BIOS after boot says "Undefined CPU at 1100MHz". I've changed in BIOS FSB settings to FSB-133/MEM-133/PCI-33. Now it says "Undefined CPU at 1466 MHz",...
Summary: i got my new board for my backup pc, but now i spent some of my money i had set aside for the cpu.got a new case. so im looking smaller. im looking at...
Summary: I am having trouble. My default setting for the FSB on my motherboard is 400MHZ...it advertises that it can do 533MHZ. I would like it to do this, bec...
Summary: Like I said, I have an ASUS A7N8X-X. I never even knew an A7N8X-XE existed until today. I'll see if I can find the manual & have a look. OK, just had ...
Summary: I am using a elitegroup MOBO with a AMD 2100 and 512 PC333 ram. When the fsb is set to 100mhz the system sees the CPU as a 1500 and everything works f...
Summary: Northbridge & Southbridge is not exclusive to Intel....AMD, VIA, ALi, & nVidia all use that configuration. I believe SiS was the 1st to go against the...
Summary: I had a similar problem with my bios, istead of running my Athlon XP 2100+ Palomino at 133FSB in the bios I had to put it at 166FSB and then it ran at...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
