Summary: You probably need to load mboard drivers. XP first came out a long time ago (2002?), what it can recognize has not changed much since then, so it may ...
Summary: Hi. In a RAID Array 0 or 1, should the IDE drives be connected as Master and Slave in the same channel or as Master, Master in different channels. Alt...
Summary: Hello I missed my drives i.e E and G and also there is a message coming mac addresses when i restart my system please help me because its a important...
Summary: I have a 'slave' hard drive fitted (my old pc's disk), have transferred the files i needed and don't really need the thing anymore (would use it if I ...
Summary: Honestly, if you are running XP with only 64mb ram my suggestion is you should format both drives. re-partition the drives into FAT32 and instal 98SE....
Summary: Hello. I have two drives. The C: has nothing and is currently my Master drive. The D: has all my programs and is currently my Slave drive. <Don't a...
Summary: Helo , I have 2 hard drives in my computer and the 1st one is split in two parts and the second one is full,, The 1st one is C drive and e drive and t...
Summary: My system has a 20GB C: drive, a 200GB D: drive, and a CD Drive on E: drive. Last night, my C: drive apparently crashed. When I tried to reboot, I k...
Summary: I had this as my slave drive for years and no problems. Then today I did a destructive recovery to my main hard drive, to roll back everything to fa...
Summary: Newer mboard bioses will recognize an IDE drive jumpered as slave if it's by itself on the 3 or 2 connector data cable, but the operating system may n...
Summary: Today, I purchased a brand new CD-RW and Floppy Drive, Because I thought my old CD-RW and Floppy were worn out or just not compatible with XP. Well, T...
Summary: I had a 32gig harddrive that i installed windows on. Then i got an 80 gig harddrive and installed xp on it again (the exact same version). Now when i...
Summary: Hello, I had a dual boot setup between Windows 98se and Xp. Xp was installed on the slave drive amd 98 on the master. Originally, the slave drive was ...
Summary: cdroms and tape drives are the slowest devices known to man or woman. make a hard drive a slave to a ata33 cdrom drive? I don't think so. but that's ...
Summary: If you installed Windows XP on both master (drive C) and slave (drive D) and you remove drive C...Windows will not boot because the boot files were lo...
Summary: COMPUTER SPECS: Pentium 4 (1.6) 512 RAM Hard Drive 1: On Motherboard IDE 1 set as Master (Quantam Fireball 30 gig, Windows XP) Hard Drive 2: On Mother...
Summary: I have my old win3.1 hard drive (conner CP30254H) installed as a slave drive in my winxp computer. It shows up as Host_for_c, drive D. When I click...
Summary: When i start my computer error message displays that "Primary slave drive fails". My bios settings are as below Primary master :- Drive c: 40 GB Prima...
Summary: Hi, This is my first post and I really hope someone can help. I've seen numerous discussions on the web similar to my problem but nothing that matches...
Summary: You don't have to mount drives in Windows. They should be automatically detected and ready to go. If it is not showing up then something is not connec...
Summary: Sorry for the confusion, I have a lot going on in my house when I was writing this. My wife is sick and I have a 10 month old son so I have to write ...
Summary: I just installed a 120 gig Seagate hard drive to back up my 80 gig Seagate primary hard drive and had a question. When I installed the new drive the ...
Summary: Dell computers use Cable Select for Ultra ATA drives. You must make sure the Cable Select is set on the drive. With Cable Select the end connector is ...
Summary: I have a 10 gig hard drive which is getting too full. So I tried adding a second drive as a slave. everything boots up fine and runs fine for awhile t...
Summary: i always here about slave drives. my impression of a slave drive is that its the second hard drive that creates an environment where one hard drive ca...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
