Summary: I have a W2K server with 2 NICs (1st NIC internal network to a switch, 2nd NIC external network to the wall jack wich is connected to a router on the ...
Summary: I have recently subscribed to a DSL ISP that provides me with a /29 subnet and 6 static IPs. I have some servers that I would like to setup with stati...
Summary: Check this out: http://www.u.arizona.edu/~trw/games/nat.htm The problem is that a Linksys router has a simple NAT firewall, and NAT doesn't handle pee...
Summary: Your post makes no sense to me. Try again in a readable form like this: internet wan x.x.x.x interface Linksys router with dhcp and nat lan interface...
Summary: In reference to the posts above... In this network setting TCP/IP should be the protocol of choice with DHCP enabled. Every computer on a network usin...
Summary: I have WIN2K server and few PC's all connected to a Dlink Broadband router w/wireless. Simple P2P setup.. I want to take it to the next level and crea...
Summary: I have to connect a small office which now have 6 PC's running Win98 & Me !. Since this is only 6 Workstations and to avoid unwanted cable layouts, Is...
Summary: I have a LAN in my home office: 1 Win98 PC 1 W2K PC 1 W2K PC laptop They are connected via TCP/IP through an SMC Barricade router. The router is conne...
Summary: Hello, quetsion. I've got a NAT server on w2K server and it works fine, but I have a really weird thing: I'm using 2 cards (I think I'm supposed to :)...
Summary: Hi, I cannot make NAT to work over my PPPoe internet connection at home. I used to run ICS and it worked fine, but all of sudden it stopped. I suspec...
Summary: I was too brief in my previous post. D is correct, the private Class C IP address 192.168.0.0 can't be used on the internet. However, if you are us...
Summary: hi i got serious problem with network under w2k It takes a lot of time to see something in network neighbourhood because refreshing directories lasts...
Summary: Hello, Would like some input on protecting internal network. Current setup is as follows: Netopia router with static public ip address. NAT to 10.1...
Summary: Hi I am maintaining a small LAN (15 workstation and 2 W2k Server). All are connected through 3com 24 port switch. I have another workstation which is ...
Summary: Could any one explain me that how I can confgiure the networking with Solaris server8 and Windows 98/2000 cleints. Solaris server should have running ...
Summary: the idea of NAT is that you use private addressing inside yr LAN and any thing going out side uses a public address from a pool, so the outside world ...
Summary: Thank Rick for the response but I understand what NAT/PAT is basically about. I also understand how ports for http/ftp etc are used. NAT allows many ...
Summary: Hello All, Here’s my setup: 1. RT314 router fully configured and working, also acts as DHCP / DNS server 2. Webstar cable modem – working fine 3. W2K ...
Summary: Hi All, I looked at my router, and found this for NAT port mapping table: --------------------- Private IP : Port #Pseudo Port Peer IP : Port Ifno Sta...
Summary: Forgot one thing... Here's the specs on both computers. The one providing internet access: Win98SE M810LMR 32mb Onboard Vd.Adpt./LAN 900mhz Duron 128m...
Summary: Essentially that's correct. All devices would show the same "real" IP as far as the outside world goes. That is to say, all devices behind the NAT h...
Summary: What is required to host my own mail server behind NAT? I have DSL with one public IP address and a Netgear router running NAT. I know I have to conta...
Summary: hi... i'm tryin' to find out how i would configure the ip addressing between windows 2003 server and a Cisco 1801 broadband router when setting up DHC...
Summary: hi! my english is not good. but please help me.it is very important for me. i have a lan with 20 computer.and a sever .i had not any problem but now i...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
