Summary: There might be other ways, but the most logical way I can think of is to connect the two dedicated rsync NICs with a crossover cable and give them sta...
Summary: Did you ever get any luck with this.? I am trying to do two nics, one ip each. one at x.x.x.2 another on x.x.x.3 I feel that being on the same netwo...
Summary: Hey, I've got some questions about Linux routing, etc. you guys might be able to answer- I've got a dual proccessor linux server with two NICs in it. ...
Summary: humm how to discribe my problem best to give a detailed system spec first. 486-DX2/66 main board with processor. 16mb of RAM vidio card n/a to this...
Summary: Hi, My PC has two NIC cards, and is running RH7.1. One of the NIC card is suddenly out of service recently. After I took out the bad NIC card, and r...
Summary: Hi There, Got a couple of questions. Hope someone can help. 1) I've got two NICs (3C905c/3C905C-TX) in my RedHat 7.2 PC. How do I set their speeds? I ...
Summary: Hi guys great forum. Glad I found it. I want to know if it is possible to have two network cards on the same subnet. I have a wireless network that I ...
Summary: I'm planning on configuring Solaris to be a router. So far I've formatted and installed Solaris 8 on a SUN station which has two NICs an internal one ...
Summary: You need two nic's. You cannot assign two ip addresses to one nic. It is impossible. Give your linux box a real ip and a private like 192.x.x.x Then g...
Summary: Hi. I run my linux machine as a firewall / router (with iptables 1.3.3). At first I had 1 nic towards wan and 1 towards lan and all worked well. For d...
Summary: I am running a TFC server on my linux machine. It has two nics installed with one hooked to an 8 port hub that is hooked to the cable modem. How can ...
Summary: How can I adjust DHCP timeout during boot up? I have two NIC's in my box set up for DHCP, and the one that is disconnected will keep trying to grab a...
Summary: Hi, I have a linuxbox which is connected to the internet and a laptop. I want to have the linux box act as a proxy server for the win laptop. I have t...
Summary: I am new to Linux and I had installed Linux 7.1 and configured mail server in which I am able to send mail to outside world and unable to receive m...
Summary: I think just set your linux's gateway to win2k's ip. This is what I did on my LAN, but all windows. Nothing to do on win2k. Only if you have two NICs,...
Summary: Set up a linux host with two NIC cards, dhcpd serving the internal network and squid for access control and proxy. Squid will control what computers c...
Summary: Hi, I have a rethat 9.0 box setup as a file server and firewall\gateway. This has two nics, eth0 is connected to my adsl modem eth1 is for the la...
Summary: Ok, that helps. Computers on network C can access computers on network B, correct? If so, you should be able to do what you're asking about without ...
Summary: Hi Everyone, I'm trying to setup an RH 7.2 linux box as a PPPoE gateway, so that I can share internet connection with my other boxes. I already have ...
Summary: I have a RedHat 6.2 with two NICs - one connected to the pivate network and the other to the Internet thru a router. I want my RedHat to act as a gat...
Summary: I'm trying to get my DSL connection working, I have two NIC's one to my DSL modem, the other to my switch. I can get the NIC's working if I give them ...
Summary: I am trying to replace our old red hat firewall and dhcp server, it currently runs an old version of red hat and has been running great for the last 4...
Summary: I have a box running Windows 98 and it is connected to the net via a cable modem. In it I have two NICs (one for the net connection, one for a LAN). ...
Summary: Note: I using the Linux:/# as the linux command prompt below IPSec with FreeSWan as the server and SSH Sentinel 1.31 as the windows client Here is...
Summary: I have set up a Red Hat 7.1 system at home. I would like to turn this into an Internet Gateway, DHCP server and Firewall for my home LAN. I already in...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
