Summary: I have a new sun blade 1500 silver that is connected to a servswitch ultra KVM (I don't have the nifty audio cables though). I know that the speaker...
Summary: We recently purchased a Sun Blade 100 with Solaris 8 to start doing some additional development on. I was wondering if anyone had suggestions, sites...
Summary: i trying install solaris 8 on sun blade 1000 machine with hard disk 36 giga byte fc-al disk bus. in first system detected hard disk but when install ...
Summary: We just purchased a Sun Blade 100 running Solaris 8. We have notice some performance problems. It runs a sparc 500mhz on 128mb RAM. With those spec...
Summary: I hope you can help me, I have a Sun Blade 100 Server with Solaris 5.8 installed. When I made an ftp from another machine to this one and I try to dow...
Summary: Hello All, We are getting a shipment of 25 Sun Blades this friday, which all need to be configuared identical to each other. My question is what wo...
Summary: im looking for an external usb tape drive 10/20 that will work on a Sun Blade running solaris 8 and i only can spend around $350 ...anyone got any ide...
Summary: Having a problem with the booting of a Sun Blade after doing a complete restore from tape. I entered this command that worked with the sparc and ultr...
Summary: Hi, I have a Sun Blade w/ a PC monitor. The monitor is three years old and stays black when connected to the Blade. Is this a matter of the monitor ...
Summary: I have a Sun Blade 2500 that I cannot get to boot from a cdrom. The discs are all operational Solaris 8, 9, & 10 discs. Each gives the exact same er...
Summary: I just bought a used Sun Blade 150 (UltraSPARC IIe 650MHz, OpenBoot 4.6, 1025 MB RAM, and Ethernet address and Host ID both listed). I am new to Solar...
Summary: Jay, Check to make sure you are running an m64 card. fbconfig -list We have run into this on the Blade 150's and 1500's. Run a man on the package that...
Summary: Hi, I have to install Sun Solaris 8 10/01 Operating System on a Sun Netra Ta1 AC 200 server. This server doesn't have monitor card. Therefore i think ...
Summary: Hello All, We recently purchased several 24inch LCD monitors and several sun blade 2000's. I installed a Sun XVR-1200 graphics card to get high reso...
Summary: FYI ... I answered my own question: When I try and boot of my Solaris 8 cd's It complains about the arch.. So I figured I should read the manual and t...
Summary: I'm brand new to Solars OS and would appreciate if anyone can help me out with the following. I got the Sun Blade 100 (SPARC|||) with Solaris 8 instal...
Summary: I am booting on an external SCSI hard drive. At the startup I get these two warning messages: Warning: pcipsy0 ino 0xc has been blocked Warning: uata...
Summary: I am booting on an external SCSI hard drive. At the startup I get these two warning messages: Warning: pcipsy0 ino 0xc has been blocked Warning: uata0...
Summary: i'm not able to detect my usb flash disk on sun solaris 9.but it is able to detect other USB flash disks of other companies with the command /etc/init...
Summary: Hi All, Unable to open a xhost console from netbackup server in my work staion. Actually i am connecting through telnet from workstaion(sun balde150) ...
Summary: Hi, Is there any way to speed up the installation of MU6 on Solaris 8 07/01 on a SUN Blade 100 machine (512MB)? By calculation, right now, it take two...
Summary: When using Unigraphics V18 on a Sun Blade 2000 with an Expert3D-Lite card, My designers are experiencing jittery rotation of large models and slow rep...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
