Summary: Hi, About "Replacement router" of August 2: Bo> I thought $150 was a bit... No Modem needed. MS> ...try 250 $ (Can) for a... ...three years MS> old ...
Summary: I just bought a Microsoft MN-700 Wireless router, and am currently connecting it to my PC's ethernet card via direct link. When connected directly to ...
Summary: - Local firewall disabled or set to treat 192.168.0.2 through 192.168.255.255 as "local" or "trusted" - Workgroup names all the same - TCP/IP installe...
Summary: My Belkin F5D5231-4 router requires frequent resets - several times a day. I have two PC's using Windows XP connected to the router. The router ties t...
Summary: I had the same problem. I was able to improve things a little by moving the router and phones around, but the only real solution came when I purchased...
Summary: Configuration: WIN ME connected to a NETGEAR Router via a NETGEAR PCMCIA ethernet adapter. Router connected to cable modem. Antoher WIN 95 sytem is ...
Summary: Replace Router 1 with the wireless router #2 and purchase a bridge or game adapter for the xbox. Dump the usb wireless adapter on the last computer. ...
Summary: A hub is similar to a cable, all data goes to all ports. A true switch can connect any port to any port so that NO other traffic on any other port i...
Summary: Hi I want to share my DSL internet connection with 2 other PCs. I will buy a router and CAT5 cable. I want to know that after replacing router with (D...
Summary: >>It really is unbelievable, I see this in almost every forum. Someone sets out in their question what they would like to achieve and instead of offer...
Summary: Easiest way to do it is to pick up a Wireless Access Point. Connect that to your router, now you have wireless capacity on your network. A more elega...
Summary: I am replacing my router/modem as I am having a lot of problems. Can anyone advise me which would be the better router/modem out of a WAG54GS or WAG3...
Summary: Previous posts that recommended turning one of the routers into just a switch by disabling the routing features may not have involved two paths to the...
Summary: I have a few questions involving using hubs and routers to connect multiple computers to the internet. I already have a hub that connects a mac and a ...
Summary: Hi I need help setting up 2 Linksys Routers my first router is a linksys router and my second is a linksys wireless router. my wired router is i...
Summary: I currently use a hub to share the DSL connection among 3 computers. I was wondering if replacing the Hub by a router would increase network performan...
Summary: First check that you have the current level of firmware installed in the router. There are several different versions of that model of router, so you ...
Summary: You could have any of several problems. 1. Defective Modem or Router. 2. You did not mention what kind of broadband connection, DSL or Cable. A weak ...
Summary: when i console into my cisco 2600 router it goes directly to the 'password:' prompt; the 'router>' prompt never appears. i don't know any of the pass...
Summary: I have had this problem twice over the past several years. The first time, I would lose connection 3-6 time per day. I would reboot the modem and rout...
Summary: Earlier on this forum I had asked for suggestions for a new router (http://computing.net/networking/wwwboard/forum/27186.html) since then new informat...
Summary: In your case I would RTFM (Read the Fine Manual) and see how to accomodate cable instead of DSL through this router. If you don't have a manual go to...
Summary: Sure, I could spend more money on more gear that might eventually work, but only an ignorant person would do that instead of trying to figure out how ...
Summary: Have you tried clearing the router and reconfigure from scratch? Here are some high points to think about. 1. is your ip from the ISP static or dynami...
Summary: Hello all, I'm in dire need for help before I lose all my hair.. I'm trying to connect 2 PCs, both XP Pro. PC A (lady) is connected to the internet t...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
