Summary: Last question first: compression does slow reading as well as writing. Network speed: keep in mind that a 100 mbit hub actually has a theoretical maxi...
Summary: i see what your sayin <vipergg> ive now set both of them to auto, as they were before i even changed them, which again set network speed at 7mbps r...
Summary: I have 2 pc's with 2 10/100 Mb/s Nics's installed, they are linked with a cat5 crossover cable and both pc's are running Winxp. If I set the Link spee...
Summary: Can anyone help? I am running win98 on a desktop and am using it as the client for a lan network. I have a 10baseT network hub and netgear network car...
Summary: I recently upgraded to a Netgear dg834g v2 Modem/router. This is a 802.11g Wireless router and the network speed should be 54Mbps. However whenever I...
Summary: It sounds like the NIC in your main computer is set to run at half-duplex 10Mbps by default. Go to your Windows settings and change it to auto-sensin...
Summary: It can't be any "faster" than it is. I had a quick look via google at this device and it's 10/100 so the maximum bandwidth you can get out of it is 1...
Summary: Does anyone know how to increase the networking speed of a 100Mbps Full Duplex netowrk. It is currently running really slow, I mean at a guess 5Mbps. ...
Summary: I have just taken over a CAT-5 Ethernet network with a number of central 10/100/1000 Switches. All of the servers are connected to a Gigabit switch w...
Summary: I have at D-Link DSL G604T modem/router with 4 computer on network (3 wireless 1 H/W). All will share network capacity except 1 has restricted network...
Summary: I had (change that to still have!) same problem, which was because i had installed the protocol NWLink IPX/SPX/NetBIOS. Uninstalling that has speeded ...
Summary: Hi All, My first time posting on these forums after years of use. Hopefully this post is successful :) My Problem ----------- I am using a hub (Switc...
Summary: My network runs on 10/100MB LAN Cards, which are networked with a HUB how would i go about upgrading my network to allow speeds of up to 100MB, rather...
Summary: Your hub and/or NICs may not be autosensing the connection speed. Investigate your hub settings (via browser, telnet, console, etc.) and your NIC set...
Summary: This is the maximum speed you can get on a 10Mbps network using a hub. Try using a switch and make sure that all devices are capable of 100Mbps transf...
Summary: HI i have been having some problems with my wireless network file transfer speed. i eventually realised that this was was greatly owing to poor signal...
Summary: Everything is both good and bad. A NAS can be used on trusted networks and perform good or better depending on type. Now they can be used across the w...
Summary: I have my laptop and desktop computer networked with a d-link router and I am wondering why the connection seems so slow. If I try to transfer a large...
Summary: Hi all.We have a basic class C network sitting behind a firewall.The vast majority of PC's on our LAN have 10/100 Mb NIC's but a few only support the ...
Summary: I have a network 1 SERVER 1 PC 1 Laptop (54G wireless) 1 54g Access Point NIC are 10/100MBPS from PC to Server the highest transfer speed you will eve...
Summary: I need some advice with speeding up my network. Please forgive my ignorance but I am just starting off in the field of networking. I have two specif...
Summary: how do I check the speed of my network cards? I got them second hand without any documentation. They are also both pci cards, so I expected them to be...
Summary: I would like to know where I should start troubleshooting my network. I have a speedstream 5200 modem with upgraded firmware to make it function as a...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
