Summary: Hello! I am the beginner of Linux kernel programming and I need your help of how to write network card driver of Linux. Could you tell me some forums ...
Summary: I have problem to configure my PCI RTL8019 network card. As I saw, there is no conflict of io addresses or irq but I got always the error message : "i...
Summary: Hi, I want to configure two network card in my Linux 7.3 system. My Linux system is as a firewall in my LAN and my client is Microsoft 95/98/NT. I ...
Summary: hi everybody. I have no idea, how to install network card driver. My NIC is D-link 5385TX. I found the driver in the Internet and i downloaded it. But...
Summary: Hello, I have dual boot PC with Linux 7.2 and win 2000. The network card works fine with win 2000. But the same card is not working. On linux the res...
Summary: Ive been trying to install my network card in my linux box Red hat 6.2 my network card is a 3com 3c059b-tpo. Ive tried what everyone said disable pnp ...
Summary: Hi all, I just installed redhat 8.0 and it doesnt detect my network card (Accton EN1207D-TX). Thats somewhat curious because other distributions like...
Summary: i'm not sure this will help but have you tried changing the jumper pins (if any) on your network card? i think it might be a resource conflict - thats...
Summary: I've got a Compaq 1211CA running a smooth xp mandrake 8.1 dual boot. The problem is I cannot configure my network card for linux, and I'm a very new u...
Summary: Hi, I just installed a network card in pentium 2 machine. It is working fine in win 95 with my cable modem(DHCP). Now, How do I use it in my l...
Summary: pls can anay one told me that how to configure the tow network card with diffrent ip like 1) is 203.133.253.3 and 2nd is 2) 196.3.72.1 pls help me .....
Summary: I've installed mandrake 9 and from the start my network card wouldn't work. I ran the network configuration wizard several times and counldn't get it ...
Summary: OK, I need help, how do I install my 3Com 3C509B (ISA) network card on Linux? I am a complete beginner and I can't figure out how to install it. I am ...
Summary: hi. Is there a way in Linux to see whether my network card is running on full duplex 100 or other? This network card doesn't seem to work with my 10/1...
Summary: I'm installing Mandrake 8.1 and when I come to the network card section, my network adapter (Linksis) is not one of the choices, so I can't figure out...
Summary: I am looking for the right driver to my network card:MOTOROLA SM56 VOICE MODEM, i have MANDRAKE 9.0. Rq:Please if you know a driver for my network car...
Summary: I have SuSE 7.2 installed on my computer. Currently I have a Netgear FA311 network card in it. Linux can't find drivers for it and all that I could ...
Summary: hi i have mandrake 9.0 when i click on connect to internet it's said connection failed i dont know why and i have DSL i think i need drivers for my ne...
Summary: I setup a Network Card in Red Hat Linux 7.1 In Netconf i put enough information then save and active the change but the network not work..I'm lookin...
Summary: Hi, I have Linux RedHat 7.2 system. After installation, I found that only loopback interface is active. I tried ifconfig eth0 192.168.1.121...
Summary: Ok here we go.......I installed Redhat 8, I was running Redhat 7.2 and my network card was working fine. The card is a Netgear FA510 PCMCIA, in my Co...
Summary: first of possible many question on this subject. Can you put two network cards on the same network..? I.E. eth0 = 192.168.1.2 eht1 = 192.168.1.3 I h...
Summary: I have a problem whose solutions I have yet to find and would greatly appreciate it if someone out there knew and could share the answer with me. My...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
