Summary: I am developing a test system under NT that uses serial ports. Is there any way to access a single serial port from multiple applications. Unix does t...
Summary: I want to access serial ports under NT in a small application written in visual C++, i have previously done this using inp() & outp() functions (acces...
Summary: I'm having trouble with NT workstation and a software pkg which detects it compatible hardware on the COM1 serial port. I know it has worked before. ...
Summary: Hello I am trying to connect to a laptop through serial port from windows NT computer.I can send messsages to a laptop and it displays it using terate...
Summary: Is it possible to read and write all serial port register under winNT? With an API, DLL...? if yes, how? ps : I program under VB6. Thank a lot. ...
Summary: On my Sat 4090 CDS (Toshiba) I install Win NT 4 sp6 instead W95 vers b. Up this migration I could not get the serial port in work. The Adress is 3F8H ...
Summary: Hi,anybody knows how to program via INT's the serial port in C++ having Win NT?I need to make a rutine for recognising a char. Thanks! Laura ...
Summary: My serial port cannot send data, only receive. I've tried removing the COM port from the control panel, rebooting and reinstalling, but it doesn't hel...
Summary: I had a workstation which an ntfs.sys error. I did a repair and the Pc booted again but the serial ports are missing. So I reinstalled them and reboot...
Summary: Anyone out there know of a good utility for changing serial port addresses and irq's My basic problem is that I have conflict between com1 and com3 (d...
Summary: Hi all, I want to send full duplex voice from serial port to modem. Is this possible? Can we send voice data from DTE(PC) to Modem over serial Port an...
Summary: I am trying to add a serial port that I found lying around to NT 4.0. I believe I have the jumpers correct for COM1 and IRQ4 and the address for COM1...
Summary: I am setting up a print server, which will need to have a minimum of 5 printers connected to it. I have a 3-port EPP/ECP 16-bit ISA EX-4017 parallel p...
Summary: Hi, I have a Dell Latitude CPxJ system with WinNT 4.0 OS installed. I have a Xircom Ethernet+Modem Card installed in this system. The Ethernet Port of...
Summary: Can a DOS program communicate with the serial port on a system running Win NT SP 4? The Hyperterminal software(on the accessories) works perfectly wel...
Summary: A piece of Visual C++ code that receive data from the serial port is written. It works properly in Windows 98. The same software does not work in NT. ...
Summary: How Can I Do a Program with Delphi or C++ Builder (for W9X), and how can I run this on W2K or WNT ? I want to do a program and I want to access the lo...
Summary: I have a DOS application that access the serial port. I need to run it under NT 4.0. The communications always fail. Is there a way to solve this prob...
Summary: Routers do much more than ROUTE TRAFFIC. Multiple ethernet ports allow for separate collision domains AND separate broadcast domains, resulting in imp...
Summary: I recently refomatted a scsi hard drive and since i have done this i can not get the Parallel or Serial port to work, I'm trying to install a printer ...
Summary: (OS: NT4.0 service pack 4)(Serial card - SIIG high IRQ) -> I installed a two port serial card (16550 uarts) to give myself two more ports. I set the c...
Summary: Well... *are* there any *.INF files? Do you see any *.INF files? Do you see any *.IN_ files? If you don't have them, I can see why there'd be a pro...
Summary: I am trying to get 80mb of files off a computer running NT 4.0 service pack 6. That's all. Here's how I've been thwarted: -There are no USB ports. -T...
Summary: Iīm using a PNP modem and it always work fine, but now the NT donīt recognise the virtual com port, i use Ports in the control panel to add a new port...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
