Summary: Mandrake 7 and Mandrake 5.3 yesterday - can't get X monitor settings right on hardware. Black screen, stripes, NW SE corners etc... Has anyone made th...
Summary: For the X-setup I need the horizontal and vertical settings for my montor. Im a bit confused when I look at stats for my monitor. This page (http://su...
Summary: I have a ASUS MoBo with that chip set 128MB 60ns RAM 4 Gig Partitioned for Red Hat 6.2 I am using onboard vidio 1 MB shared Mem. This seames to A memo...
Summary: You don't generally use drivers in linux..for your monitor you should just be able to use the custom setting (assuming you are using Xconfigurator) an...
Summary: Hey all, Was installin Redhat 9 today and when it probed for my monitor apparently detected the wrong thing and (i wasnt paying attention) i clicked n...
Summary: I'm running a dualboot system and I find that if my screen's aligned in windoz, it's not aligned in FC4. Is there a way round this, are monitor settin...
Summary: It sounds more likely that it is your monitor setting which is wrong, otherwise you wouldn't get a blank screen but error messages instead. Was you...
Summary: Unfortunately this is one of the (few) weaknesses of Linux, or more specifically X windows. The problem is that your X server settings are set for you...
Summary: Sounds like is telling you "monitor frequency out of range". If so, all you need to do is adjust your video card and monitor settings (hor, ver, frequ...
Summary: brother are u new to linux or an expert. try #Xconfigurator * your monitor settings are not good. try a diffrent one using the above command. ...
Summary: I am trying to load Linux Mandrake 8.2 as a second os on my p2 333mhz system. I have partitioned it with partition magic pro 7. The system has Win98...
Summary: Well, my monitor just quit on me, so I had to get rid of it. I've switched to another one I have, and the computer went into Windows XP just fine. How...
Summary: Monitor settings are done through X configurator. ie, command "xf86config" , "xf86setup" or "Xconfigurator" depending on your distribution. Good Luck...
Summary: I've recently added a 17inch TFT monitor to me RH9 machine. Now when I boot up I'm getting a blank monitor at the final stage of bootup. Is there anyw...
Summary: I had installed Linux and was setting up everything and then i changed my monitor setting from a 16 bit to a 24 bit. When I restarted the computer, th...
Summary: XConfigurator not working? K then type xf86config on the prompt, that will open a text based configurator. To configure Xfree86 with it, you have to k...
Summary: ahem... Type startx if you configured your video card and monitor settings during install, otherwise type "XF86Setup" and configure first. Tum dono ek...
Summary: FREEEEEE Windows sux On My windows O/S I have to install drivers from a disk... with Linux I just tell it to do it an its done an Im on the net... onl...
Summary: cntl + alt + backspace using tabs choose failsafe login see if it works if not use cdrom to boot into recovery mode from console type xf86config (you...
Summary: Hi, This document i´ve found, works on my presario. I hope it works on yours too! excuse my english and good luck!!! COMPAQ PRESARIO 1200-XL110&111 ...
Summary: Who got my post saying to fiddle with the monitor settings deleted? I mean That could well have been the problem, i'm sure we've all had to do it at s...
Summary: In RedHat 7.3 you would use Xconfigurator and just use generic monitor settings. But they may have dropped that from 8.0 being how they dropped everyt...
Summary: The xset command requires the xserver to be running. So if you booted in text mode then it won't work even if you set the display variable. Have you r...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
