Summary: I recently installed a Linksys router to my network. After setting up the router I tried to log in. The log in was VERY slow and also any network ...
Summary: Hi ddimitrov, Last week we had similar discussion (http://computing.net/networking/wwwboard/forum/20721.html). The consensus is that it does not look...
Summary: A 10/100 router connected by CAT 5e wiring to each PC will give you up to 100Mbps on each port so the router itself won't slow down either connection ...
Summary: I just set up my home networking. My brother and I are on LAN. He like to download things using Kazaa. When he is downloading, my internet usually slo...
Summary: Hello, I pulled out my old Linksys router that I bought a few years ago so I could connect my 360 along with my PC. However, when booting up either t...
Summary: Hello all! I've been searching all through this forum and I can't seem to find an answer to my problem even though it seems a lot of people have trou...
Summary: Hi, I have a Linksys BEFW11S4 v2/v3 gateway router. I have 4 PCs connected to the router and also one laptop for wirless access. DHCP is enabled. I wa...
Summary: I have a linksys WRT54G router, of which I've had for 3 years. Never had a problem until this past week. Recently I decided to drop my cable internet...
Summary: This is my third router because the other two were both claimed to be defective by Linksys. This router is having the same problem as the other two so...
Summary: I just set up a Linksys router from my cable modem then out to two pcs (1 2k, 1 xp) which were previously networked by a hub and working that way. We ...
Summary: Whoa slow your roll there tonto ;) No need to do a fresh install of anything... Ok lets start from the beginning now. Make sure both computers TCP/I...
Summary: Hey persons, Maybe someone can help me with this. I installed a Linksys router and everything worked fine. I changed from DHCP to static in order to p...
Summary: From the factory the Linksys router is set to block all LAN requests. That meens your cable service can not Ping the router to see if the IP address i...
Summary: I am wondering what it takes to get my router working again when my dsl disconnects. I have a linksys BEFSR41 wired router and AAT&T yahoo DSL. The DS...
Summary: I am going to purchase another ip address so i can use a hub uinstead of router(so i dont have a firewall) and i was wondering if i used a 10 mbs hub ...
Summary: Also, my understanding is that a router shoud transfer data at 100 Mbps via cable and and up to 54 Mbps wireless. This is much higher than your modem ...
Summary: Hi, I'm having a problem with my home network that I'm hoping someone can help me with. I was using a Linksys router, then switched to a Neatgear WTG6...
Summary: first ooff lets get some teminology right...what do you meen by live ip's and direct, ie dhcp or static. The way you say this net is setup is a little...
Summary: Hello all, my problem is that the modem i got from globe has an ip of 192.168.1.1 and the linksys router has the same ip. This prevents me from connec...
Summary: My linksys router also did that. It only happened when the hosts were configured for DHCP. When I switched over to static IP address on the LAN it di...
Summary: Hi i have a linksys router with a NAT firewall in it. Is there anyway to totally turn of this firewall? i went todmz hosting and static routing but wh...
Summary: Recently I purchased a Linksys Router. I know you can access the GUI via webpage if you put in 192.168.1.1:80. What I want to know is it possible to a...
Summary: When setting up any Linksys router out of the box, I've discovered (the hard way) that it's practically mandatory to push in the reset button first f...
Summary: Hello! I do my best to help people on here so now hopefully all you wonderfull people will help me. I've googled this many different ways but i'm no...
Summary: Alright, Im trying to get 2 pcs networked so that they can both go on the internet. I bought this Linksys Router (Model BEFSR41). And here are the man...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
