Summary: I got two old hard drives from a college garage sale but all that is on them is Conner & made in Malaysia. They have more numbers. ACB3Y58 CP30064H GA...
Summary: Boot with a floppy. Check which drive is C:. It is probably your "slave" drive with no operating system on it. If this is not the case, there ...
Summary: I put a new hard drive in my computor about 8 months ago. There was nothing wrong with the old hard drive, it just didn't have enough space & I wante...
Summary: First check that all the ribbon cables are connected and snug. Then check in the bios that the hard drive is listed. When you get the hard ...
Summary: i downloaded versions 5, 6, 6.21 and 6.22 of DOS. when i load into DOS, my hard drive is not detected. i got the version from bootdisk.com and pchelpl...
Summary: we got this free Laptop and this Laptop has no Cd-drive .When we try to start the laptop we get the C:/ so i guess the DOS is loaded(though i donot kn...
Summary: I have reformatted a PC clone with partitioned drive. Formatted c: I want to reinstall windows. I have the CD. I have a CD driver. What I don't have ...
Summary: I just bought a dell latitude laptop, and had the seller put a brand new hard drive in it. I installed Dos 6.22 from the 3.5 drive with no problems. ...
Summary: Boot with a floppy disk and run Scandisk. If you are going to reformat the drive Format will mark any bad sectors. There is no reason why you c...
Summary: Depending on the age of the BIOS, you may be able to set it to auto-detect your hard drive. Look through the menus and look for that sort of option. ...
Summary: Hi Pennie, There is no command in DOS to start a network but you can download a little Programm called MSClient (ftp://ftp.microsoft.com/bussys/Client...
Summary: Take a look at the drive with delpart. (It's a Microsoft product.) http://hercules.lss.ksu.edu/download/MSSTUFF/delpart.exe It'll remove pretty well a...
Summary: since when is it an 8.4 gb limit, i have installed ms-dos 6.22 on my p2 systems 20gb harddrive, with no problem, setup formated 2gb, and i made the re...
Summary: Patrick, sys c: would have done you no good in this case as you were able to boot to dos. You had an OS already. I agree with the Micron person at t...
Summary: Well, it's difficult to say, but I would guess that it's due to using a drive with a greater capacity than the BIOS was programmed for. If it passes ...
Summary: A 486 will recognize a 500MB HD with no problems. A capacity-recognition utility is required for 2 gig or greater drives. I have two 486s each with a ...
Summary: Did you try Norton DiskDoctor first? If not, try it NOW. It recovered almost everything (lost 6 files out of 10,000) from scratch when the partition t...
Summary: I'll try to walk everyone through the situation. Okay, at first the drive was FAT32 with a Windows 98 SE installation, and I know this for fact. Then...
Summary: Hello, I know this is a common problem, I've looked at most of the messages on this web site. I'm trying to partion 10GB drive in fdisk, so I DOS ca...
Summary: Be that as it may, the reason for using option (4) in this case is to determine the drive's System, which is not displayed by the /status switch. It'...
Summary: > but after i deleted the primary drive Are you using more than one drive? If so, make sure you're selecting the correct drive with FDISK. Did you de...
Summary: lol calm down. you may want to make sure that the drive has been given a drive letter (like "C") so check to see if it exists...boot from the disk you...
Summary: Make sure the drive is the only drive in the system, and on the IDE channel 0, and it is bumpered as a Master. Then try booting with the Windows ME S...
Summary: i had to fdisk hard drive and lost access to cdrom in dos mode while runing win 98. i need dos drive or driver configurations for a matsus---a-kotobuk...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
