Summary: I posted earlier about a problem I had and I'm getting, hopefully, a little closer to figuring out this problem. Refer to message # 35595 Apparently ...
Summary: I have 2 x 256MB of PC3200 CL2 DDR RAM, I was in my BIOS today and here is the current setting for them: T(RAS) 7 T(RCD) 3 T(RP) 3 CAS Latency 2 But,...
Summary: Hi Anyone know what settings I should make in my bios for the FSB speed and DDR frequency? I have MSI 745 Sis Ultra motherboard, Athon 1.8 xp and 256 ...
Summary: If it won't boot with the ram in the slots for dual, move one of them to the other slot. That will place both sticks on one channel. The performance...
Summary: I have a question regarding Compatibility of DDR 333/400 memory with my i845PEBT2. hopefully someone can asnwer as I only have minimal hardware exper...
Summary: Hey, I'm hoping someone here can give me some insight on my problem. Before I start, here's a rundown of the system: OS: WinXP Home SP2 CPU: AMD At...
Summary: I have just installed an additional 512 DDR 2100 Memory. Since installing my PC keeps crashing and doing strange things when in use........resulting i...
Summary: how can i tell if my bios is setup properly and i am getting the 333mhz speed for my pc2700 ddr memory? and how can i tell if i am getting the full 53...
Summary: that board wont support it that board is unstable with most 2100ddr speeds, i have read some on reviews in other forums on that board of yours, don't...
Summary: (Sorry I posted this in the wrong section earlier) Hi, a bit of a newbie question for you. I am getting a P4C800 Deluxe MB with a P4 3GHz(800FSB) CPU....
Summary: I recently purchased a Corsair XMS Platinum(DDR 1GB TwinX1024-3200C2PT) And for the record I'm a "newbie".I built this baby a week or so ago, but I'm ...
Summary: yea, it can go 400mhz, it's a nforce2 board. but i am still confused though. i am not entirely knowledgable, just had some experience. and my experie...
Summary: You are confused about the memory specs. The memory you have is DDR2700, the memory you want to upgrade to is DDR2700. Your MB supports DDR3200 whic...
Summary: Hello everyone, I'm trying to figure out what to set the settings in my BIOS for my memory because when I set my BIOS for optimized settings, it runs ...
Summary: It is uncommon that installing greater than 256mb on a win98 system makes a noticeable performance difference. Multimedia editing is one example, suc...
Summary: I've got a little primer on Dual DDR and I know how it is to be set up on my new Soltek but.... Will it do anything on my PC because my processor is ...
Summary: i just bought an ASUS A7N8X mobo and it supports dual channel ddr..i installed a stick of pc2700 in the proper slots and sandra still says my memory b...
Summary: I have this same set up you need 2 sticks,and put them in either 1 and 3 or 2 and 3 to get dual.As Tropic said its reading fine but get 1 more stick o...
Summary: I thought EVERYONE knew this stuff by now! Do the math. Your AXP 3200+ runs at 2.2GHz (aka 2200MHz) with a multiplier of 11x. The multiplier is locked...
Summary: cpu= 2700+ ram= 4 2700 kingston hyperx mobo= gigabyte k7nnxp ok 2 questions fisrt, is there a way to take my dual channel ddr off and run them all on ...
Summary: I have a Anthlon 1400 mhz computer os is windows me.I was woundering if someone would know a website I could check config setting for my bios.My mothe...
Summary: "This means that the DDR 2700 512M has no problem" 1st of all, since your Sempron runs at 166MHz (333FSB), make sure to run your RAM at the same speed...
Summary: When my box boots, it reads ddr frequency 320. I purchased ddr 3200, 1 g of it, should that read ddr frequency 400 then?? Can anyone confirm that, o...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
