Summary: As the other guy said: [START] ---> [RUN] --- enter "cmd" this will bring up a dos box. then type "ipconfig/all" to show the info you have "ipconfig/r...
Summary: the router basically is a hub, but allows Internet feed as well. Just dont plug any ineternet connection in the WAN port sorted Regards, Jamie McCoy ...
Summary: I have a concern with my wireless router. When I first installed it to my DSL connection I didn't enable WEP, but later I realized that the reason my ...
Summary: Yesterday I just bought a brand new Linksys Wireless - G Cable Gateway, Model No: WCG200. It is a new type of consumer networking device that combines...
Summary: I have four networks all using hubs that I need to access the internet. I have a DSL connection and a 4 port Linksys router. How do I connect the net...
Summary: I think TECHNICALLY it is possible to set that up, but I have found nowhere any discussions on how this might be possible (to share a cable/dsl connec...
Summary: I recently aquried a 24port 10/100 dual speed hub made by centrecom that was extremely cheap and works fine for my use. I know what the 100 BASE TX ...
Summary: "why should i buy a router?" Because if you don't... "a hub will work fine i just want to know if it will put all of my compters on the internet with...
Summary: I have the Etherfast Wireless Access Point + Cable/DSL Router (BEFW11S4 v2). I am having trouble FTPing...running as client, FTPing into my webspace a...
Summary: 1.) Each NIC card in the PCs must be rated at 100 Mbs, or 10/100 Mbs (the second option does a sensing of your network and set to the highest rating ...
Summary: I think it's kind of presumptious to presume you wont see any performance increase without knowing how the network is operating currently. I've seen...
Summary: Hello Friend! If u r planning to network just 2 computers, then u dont need a hub, but u can use it if u want. Hub is used where there r more than 2...
Summary: Dave02, with all due respects, I don't think that link you keep posting is very clear for new users. CC, if you have a Linksys router, not just a hub,...
Summary: bulloney The problem I had with the IRQ was only found out with the diagnostic disk that came with my NIC. It said that the IRQ was set to 255 (honest...
Summary: COMMON DAVE!! dont give him some crap from a website. a switch very similar to a hub but a switch is used for broadband connections to share one line....
Summary: Yes you can use it as a hub. Configure your workstations to dhcp. They should grab a address from the router. But if you got the wrong unit why aren...
Summary: I don't want to dissagree, but the way my isp works if I understand it corectally is that there is only one modem for my entire town (It is a very sma...
Summary: I am using the wireless router my roommate has, it is a basic Linksys wireless router supporting only 802.11b. It has no 'g'. No speedboost. My wir...
Summary: i left this message last week "will i have a problem connecting 2 computers to a bt adsl connection? the 2 computers are running xp and are connected ...
Summary: I tried this once before but the post got all messed up. So, here I go again. I have 2 computers connected with a Cat5e Crossover cable. One is a De...
Summary: Hi, I have 2 computers connected with an UTP cable, I dont have a hub, but is there any program that make both get to Internet? (O.S. win 98) ...
Summary: The issue is with using the two routers. What you should do is leave your first router (the one connected to your modem/the internet) as is. Then run ...
Summary: "You MIGHT be able to put in some AT commands for the one modem to tell it to not check for dialtone. Then you MIGHT be able to hook them direct to ea...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
