Summary: Made use of it.......lol........looking at one right now connecting my PC to my Cisco 2900 XL switch. We have a ton of them at work. It's a "console...
Summary: Hi, Can somebody teach me how to configure Cisco 2900 switch so that it will run on 100BaseT? Or how to check the current running link speed.Please ...
Summary: If I plug a rj45 cable from a cable modem into a 24 port Cisco switch, will that give me Internet access accross the remaining 23 ports? Not without...
Summary: First off....calling them routers is a bit of a misnomer. What they are is a switch with built in NAT and firewall technology. They do do some simpl...
Summary: Your router won't do anything with the packet unless the port it's coming in on is also tagged for the VLAN the packet is. It doesn't necessarily hav...
Summary: Jefro, where did you get that switch info? It's total bunk. That may have had some small level of truth years ago when switches were in their early st...
Summary: I currently have a 10.10.0.0/16 network that I would like to re segment to 10.10.0.0/17. Currently I have about 20 work group level cisco 2900 series ...
Summary: Are you sure wanderer? It seems to me you only need a crossover cable when connecting like devices. ie: router to router, switch to switch. I know...
Summary: THe SBS's are going to be seperate domains that was my plan all along. Virtualization I have never used and will have to look that up. Any suggestions...
Summary: Cisco is good, 3500 is pricey. With you only having 10 PCs and not needing many features it would be more cost effective for you to look at the Cisco...
Summary: I couldn't agree more about the UPS! On any network device like a switch or router and/or servers you don't want to run without them. I'm not going ...
Summary: Jefro: Don't forget that your "router" is little more than a hub. At about 40% bandwidth it will begin to slow down. It is still a far cry better than...
Summary: That's kind of a tough question to answer without more in-depth knowledge of your setup. In a nutshell....yes...VLAN's are good idea in a larger envi...
Summary: Dave, Some switches can be configured to do this, but not all. A switch merely is a sort of smart hub. To do load balancing on a switch, you need a fa...
Summary: Use a crossover cable Someone else may pipe up and chime in and say you don't have to use a crossover. While this may be correct since most, if not al...
Summary: Dear all, i have a requirement of pulling Cisco router/switch startup config to a tftp server, most of my IOS are below version 12.2 so I cannot try ...
Summary: I use a work computer from home, it connects to email through a Cisco VPN client, and I am consistently getting error message 412: the remote peer is ...
Summary: Have a Cisco 1720. To use the dial in remote access do I need a modem or can I simply connect in a standard phone line with dial tone directly into t...
Summary: I am trying to deploy several Cisco 1242 access points. I am using power injectors to power the devices, but the status light stays orange. If I plu...
Summary: Hi, I wonder if i may run a few questions past you guys. We have a Cisco 1700 at one of our sites which is supposed to be managed but due to problems...
Summary: Hi, I am new to cisco catalyst switches.I need to change hostname for one of cisco catalyst swich.How do i do that.Can some one provide me the steps ...
Summary: I currently have 5 Cisco 831 VPN setup using ah-md5-hmac esp-3des esp-md5-hmac encryption I am interested in purchasing a Cisco 1811 Broadband router....
Summary: Ok, question for all the Cisco folks. I purchased a Cisco 1417 router on ebay to replace the router provided to me by my ISP (A 2Wire Wireless GW rou...
Summary: I am trying to enable port scaning on a cisco 3560. When I do it shuts the interface down. I am running an IDS on the destination port and need to acc...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
