Summary: Hi everyone. We one a cisco router that and outside company installed and that no one knows the password to get access it. I basically need to get in...
Summary: Have a Cisco 1720. To use the dial in remote access do I need a modem or can I simply connect in a standard phone line with dial tone directly into t...
Summary: I am setting up a WAN with 2 cisco 1720 routers on a 256 leased line. In the configuration manual, there does not seem to be much info as far as sett...
Summary: Having a problem setting up IPX over a T1 on a Cisco router. I have a different kind of router on the other end, but I can't even type IPX commands o...
Summary: I need to provide connectivity from a public IP 66.162.230.226 (ports 21 and pcanywhere ports 5190, 5191?) to the same ports on a internal machine wi...
Summary: Hello I have purchased 2 Cisco 1720 Routers with WIC 1DSU T1's in them. I have a T1 Circuit from the Phone Company, How do I configure the Serial Inte...
Summary: when i console into my cisco 2600 router it goes directly to the 'password:' prompt; the 'router>' prompt never appears. i don't know any of the pass...
Summary: Hi there, I got 16 IP addresses from my ISP. I have Cisco 1720 router. The problem is that I can't ping my router. I made connection as follow: PC->3...
Summary: Hi, I wonder if i may run a few questions past you guys. We have a Cisco 1700 at one of our sites which is supposed to be managed but due to problems...
Summary: in the Cisco Site there is the complete method for doing it in (Router Config) Section and password recovery article go ahead and do it.... if still u...
Summary: Trying to configure 1720. have 1 wic 10baseT card installed. One static ip is input to this interface ethernet0. Putting out dhcp thru the 10/100 ethe...
Summary: Hi there, Is there posibility to make monitoring on routers? I have Cisco router 1720 and I have about 20 users on my network. I would like to know i...
Summary: Goto the Cisco site www.cisco.com and do a search on password recovery for a 1750 cisco router, you HAVE to be directly connected to the console port ...
Summary: You need to run the password recovery procedure. To do this you need to make a console connection to the router. This requires a DB9 to RJ45 converter...
Summary: During an ill fated password recovery on a Cisco 1601 Router I put in a wrong statement for a register setting. I assume that this is my problem but ...
Summary: It might be better if you setup a VPN (IPSec) on your Cisco router other then using port forwarding ,it could open holes on your network for attacks....
Summary: He download the the wrong IOS and install the wrong one too. You can get by doing a password recovery and enter a hex number to bypass the boot-up s...
Summary: Because of our location, we can only get T1 capabilities. Communications company sold us on a single channel T1 as an option to DSL/Cable and proceed...
Summary: I have a cisco 1720 router and need to map a public ip to a local ip. Can some one please help me. Trying to set internal email and post a webpage. ...
Summary: i have a linksys 4-port cable router. an admin password has been set that we cannot figure out. is there anyway to disable or hack the old one to ch...
Summary: I am in the process of purchasing a cisco 1720. I am unsure what I need. I know I have a frac/T1 so I'll need a wic 1t card. But I was told I could mo...
Summary: Just setup a Cisco 1720 router and I'm having problems running IPX through a serial connection out over a T1(PPP). Not sure if I should use IPX or IPX...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
