Summary: Hello, Does anyone have a solution to my problem. I have this 3Com 3c509b COMBO and I was trying to install Windows NT 3.1. As network adapter, I inst...
Summary: I am having a little difficulty install my NIC in my computer. I am running Windows NT 4.0 workstation service pack 6. I am trying to install a 3Com...
Summary: I need some help. I have a small network of 15 computers. I have a NT 4.0 Server SP 6 with two of the same model isa 3com network cards installed in ...
Summary: I just installed a 3Com "3C509B-Combo" NIC in my Windows NT 4.0 workstation service pack 6 box. I have not run any cable to it. I am curious though ...
Summary: Does anyone know how to install a 3Com 3C509b-TPO card in a DOS 6.22 machine... I have an old DOS machine that connects to a Novell 4.11 server...whic...
Summary: I am having trouble communicating between two NT Servers. I can ping each server's IP loopack address and each local computer's IP address but cannot...
Summary: I am using an evaluation copy of NT Server 4.0 for educational purposes and have had a lot of trouble communicating between my two-computer setup at h...
Summary: I am having a problem installing 2 network cards in my NT Workst. When I install the second card, everything is fine, until it asks me to put it o...
Summary: I unfortunately am only working with two computers so I am limited as far as my testing and troubleshooting. I am using 3COM 3C509B Network cards for...
Summary: Hi, i have a problem with 2 exact 3com nics, (3c509b ISA), both pnp disabled with etherdisk utility, with I/O 300 - 310 and IRQ 10 - 11. I configure w...
Summary: error msg: could not start 3com 3c59x bus master adapter driver service on \\inet error 0031: a device attached to the system is not functioning ...
Summary: Hi and thank for taking a look on this. I'm haveing trouble with my laptop, i'm installing a new NetworkCard to it. The Computer is a Toshiba SatPro 4...
Summary: Hey, my Problem is I have an Notebook from Toshib (Tecra) and I have a NetworkCard from 3Com (3CCFE575BT).Under NT ihave this Problem: I see the Net, ...
Summary: Trying to install NIC on my home NT server...using an old Dell 75 pentium...tried a cheapie, $12.95 NIC advertised for NT...locked it up... I have a 3...
Summary: Please Help. I am working on a PC that is part of a network (4 Clients) 1 File Server all running NT 4 Service Pack 6. The server uses MindSring ISP...
Summary: Have NT.4 plus Service Pack 6 on a PC. I installed 3com 3C905B-TX-NM driver for network. Everything seemed to operate normally. When I rebooted the ...
Summary: Hi. I have just installed NT4 Enterprise editon at a compaq Prosignia (don't know which type) Its a P1 120Mhz with 65Mb EDO ECC ram. In the beginning ...
Summary: I am trying to install drivers for a 3Com PC Cardbus onto a Toshiba Tecra8000 running Win NT. It acts as if they install,I accept the defaults, I get ...
Summary: I am trying to create a dos boot disk for a 3com pcmcia nic card model# 3ccfe575bt. My ultimate goal is to have a toshiba satellite pro 4260dvd login ...
Summary: I have run into this several times, most recently with two 3COM NICs. I am unable to have NT 4.0 Workstation identify the NICs as independent. There...
Summary: I need to know where to find NT drivers for a 3COM Impact IQ isdn external modem. When I go to 3COM I find nothing but firmware upgrades. Help !!!!!...
Summary: I have several machines running NT4 and I now want to network them together. I have a 3Com 10/100 16 port Hub. I have 3Com Ethernet cards. Having n...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
