Summary: Hello, I have a DSL modem, and a Cisco 2950 switch. Do i need a router in between if I want the computers connected to the switch to have access to th...
Summary: Hi all, I have problem on my cisco access server Configuration Using Invalid IP address for Asynce Port , my cisco access mojule use Invalid IP addr...
Summary: I use a D-link DI-713P router at home. I wanted to monitor the data coming from my cable modem (or tap it). Is there any way I can mirror or "span" (s...
Summary: You have 2 choices: 1. Get a DSL modem and plug it into the wall jack. Then plug the DSL modem into the Linksys routers WAN port. Have the 2 other com...
Summary: You know they make routers with multiple wan interfaces to do just what it appears you want to accomplish all in one unit with load balancing/failover...
Summary: Hi expert guys there: my company needs to setup voip on corp LAN. I read cisco stuffs and try to understand the concept. here i have a little confuse ...
Summary: Please help and give advice: My company has 2 different models of PIX,one is 515E (UR) & 515 (R). 515E has 5 interfaces (but only 3 in use, which are ...
Summary: Hi, For some reason I am unable to telnet a switch on my LAN and get the message: Could not open connection to the host, on port 23: Connect failed I ...
Summary: Hey guys! I bought a Planet Layer 3 switch to install at my company. I have two local subnets which are: 192.168.1.0/24 192.168.20.0/24 Now, after I c...
Summary: how to set up two branches of banks to work in correspodance. which software will i used. please some one should help me out of this situation. i a...
Summary: All VLANS are connected to fastethernet 0/0,and both ISPs will be connected to fastethernet 0/1 So what you're saying is: fa0/0 = internal interface ...
Summary: The basic flow of the process is: User end(core router) > Switch (Cat6500 for distribution) > Servers. The users create telnet sessions. These users i...
Summary: I have a basic "access port" and "trunking" based VLAN question. Suppose I have a Cisco switch terminated to the following devices: FA0/1 terminates t...
Summary: I have a 8 & 24 port cisco switch, I have tried to configure a VLAN in 24 port switch and I can, but when I tried to configure a VLAN in 8 port switch...
Summary: If you have two standalone cards assuming 100mb you get 200mbps per card in full duplex. So if you have two cards you have (2) 200mbps xfers. This is...
Summary: Hi All, I have a Cisco 1605 router that connects two networks. Each ethernet port has been configured for the networks (IP/subnet), I have enabled IP...
Summary: My current network configuration is: DSL modem and wireless router has ip 192.168.2.1. This has two PCs with network cards hard plugged into the route...
Summary: I've just purchased a router and I was wondering what the better configuration would be. I am not even sure if one of them is even possible. Broadban...
Summary: I have a customer who had a fractional T1, and now has DSL. He has a Cayman Router from their ISP configured for the DSL, but they already had some N...
Summary: I've used ethereal on lots of Windows machines with a variety of nics (on board, ISA, and PCI) and have never had a problem with ethereal on Windows a...
Summary: They both would work and both support Cisco IOS, however, the difference between the 827 and the 837 is that the 827 has 1 ADSL port and 1 10BaseT Eth...
Summary: I have a network (2 computers) set up with a Netgear HUB, I have 2 nics in one system for internet sharing of my cable modem... Here is a list of ever...
![[higher confidence]](http://static.computing.net/img/AT-red_x.gif)
- higher confidence, ![[lower confidence]](http://static.computing.net/img/AT-black_x.gif)
- lower confidence
