Computing.Net > Forums > CPUs/Overclocking > Help System Board is to high temp

Computer Problems? Computing.Net has over 1,000,000 posts about all things technology related! Over 90% answered within 24 hours! Click here to start participating now! Also, be sure to check out the New User Guide.

Help System Board is to high temp

Reply to Message Icon

Name: shabarox
Date: October 23, 2004 at 15:15:23 Pacific
OS: windows xp sp2
CPU/Ram: 1024 mb ddr 400
Comment:

SiSoftware Sandra

System
Manufacturer : System Manufacturer
Model : System Name
Version : System Version
Serial Number : SYS-1234567890
ID : 00000000-00000000-00000000-00000000

System Chassis
Manufacturer : Chassis Manufacture
Type : Tower
Can be locked : No
Version : Chassis Version
Serial Number : Chassis Serial Number
Asset Tag : Asset-1234567890
Boot-up State : Safe
Power State : Safe
Thermal State : Safe

Mainboard
Manufacturer : ASUSTeK Computer INC.
MP Support : No
Model : A7V600
Version : REV 1.xx
Serial Number : xxxxxxxxxxx
System BIOS : 09/02/2004-VT8377/VT8237-A7V600

System Memory Controller
Location : Mainboard
Error Correction Capability : None
Number of Memory Slots : 3
Maximum Installable Memory : 3GB
Bank 1 - DDR 1 : DIMM Synchronous DRAM 512MB/64
Bank 2 - DDR 2 : DIMM Synchronous DRAM 512MB/64
Bank 3 - DDR 3 : Empty

Chipset 1
Model : ASUSTeK Computer Inc VT8377 Apollo KT400/A/600 CPU to PCI Bridge
Bus(es) : AGP PCI IMB USB FireWire/1394 i2c/SMBus
Front Side Bus Speed : 2x 166MHz (332MHz data rate)
Maximum FSB Speed / Max Memory Speed : 2x 200MHz / 2x 200MHz
Width : 64-bit
IO Queue Depth : 4 request(s)

Chipset 1 Hub Interface
Type : V-Link
Width : 8-bit
Full Duplex : Yes
Multiplier : 1/1x
Speed : 8x 66MHz (528MHz data rate)
IO Queue Depth : 9 request(s)

Logical/Chipset 1 Memory Banks
Bank 0 : 256MB DDR-SDRAM 3.0-3-3-6CL 2CMD
Bank 1 : 256MB DDR-SDRAM 3.0-3-3-6CL 2CMD
Bank 2 : 256MB DDR-SDRAM 3.0-3-3-6CL 2CMD
Bank 3 : 256MB DDR-SDRAM 3.0-3-3-6CL 2CMD
Bank Interleave : 4-way
Speed : 2x 199MHz (398MHz data rate)
Multiplier : 6/5x
Width : 64-bit
Power Save Mode : No
Fixed Hole Present : No

APIC 1
Version : 0.03
Speed : 16MHz
Multiplier : 1/2x
Maximum Interrupts : 24
IRQ Handler Engaged : Yes
Enhanced Support : Yes

Memory Module(s)
Memory Module 1 : Xerox 512MB 16x(32Mx8) DDR-SDRAM PC3200U-344-650 (CL3 up to 200MHz)
Memory Module 2 : Xerox 512MB 16x(32Mx8) DDR-SDRAM PC3200U-344-650 (CL3 up to 200MHz)

System Clock Generator
Model : ICS 94228
Software Programmable : Yes
Read-Back Support : Yes
Speed Selected By : Software
Spread Spectrum Modulated : Yes
Number of FSB Speeds : 32
FSB Speed Range : 67 - 233MHz

Environment Monitor 1
Model : ITE IT8705/12 ISA
Mainboard Specific Support : No

Temperature Sensor(s)
Board Temperature : 57.0°C / 134.6°F
CPU Temperature : 43.0°C / 109.4°F

Cooling Device(s)
Auto Fan Speed Control : No
CPU Fan Speed : 3041rpm

Voltage Sensor(s)
CPU Voltage : 1.74V
+3.3V Voltage : 3.33V
+5V Voltage : 4.92V
+12V Voltage : 11.79V
-12V Voltage : -16.97V
-5V Voltage : -8.78V
Standby Voltage : 4.92V
Battery Voltage : 3.22V

AGP Bus(es) on Hub 1
Version : 3.05
Speed : 8x 66MHz (528MHz data rate)
Multiplier : 1/2x
Fast-Writes Enabled : No
Isochronous Mode Enabled : No
Addressing Enabled : 32-bit
Aperture Size : 128MB

PCI Bus(es) on Hub 1
Version : 2.10
Number of Bridges : 1
PCI Bus 0 : PCI (33MHz)
Multiplier : 1/5x

LPC Hub Controller 1
Model : ASUSTeK Computer Inc VT8237 PCI to ISA Bridge
ACPI Power Management Enabled : Yes
Multiplier : 1/4x
Speed : 8MHz
DMA Multiplier : 1/2x
DMA Speed : 4MHz

USB Controller 1
Model : ASUSTeK Computer Inc VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 2
Model : ASUSTeK Computer Inc VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 3
Model : ASUSTeK Computer Inc VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 4
Model : ASUSTeK Computer Inc VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 5
Model : ASUSTeK Computer Inc VT6202 USB 2.0 Enhanced Host Controller
Version : 2.00
Specification : 1.00
Interface : EHCI
Channels : 8
Companion Controllers : 4
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps) High (480Mbps)
Addressing Support : 32-bit
Legacy Emulation Enabled : No

FireWire/1394 Controller 1
Model : Creative Labs Audigy 2 Firewire Controller
Version : 1.10
Interface : OHCI
Enhanced Support : No
Channels : 64
Speed : 400MHz

System SMBus Controller 1
Model : VIA VT823x SMBus
Advanced TCO Mode Enabled : No
Slave Device Enabled : No
PEC Support : No
Speed : 16kHz
Multiplexor : Asus IO mux

Expansion Slot(s)
PCI 1 (1h) : PCI 32-bit +5V +3.3V PME Half-Length Available (VIA Technologies Inc ProSavageDDR P4X600 CPU to AGP Bridge)
PCI 2 (2h) : PCI 32-bit +5V +3.3V PME Half-Length Used
PCI 3 (3h) : PCI 32-bit +5V +3.3V PME Half-Length Available
PCI 4 (4h) : PCI 32-bit +5V +3.3V PME Half-Length Used
PCI 5 (5h) : PCI 32-bit +5V +3.3V PME Half-Length Used
PCI 6 (6h) : PCI 32-bit +5V +3.3V PME Half-Length Available
AGP (7h) : AGP-8x 32-bit +3.3V Half-Length Used

Port Connector
PRIMARY IDE/HDD : None - ATA / None
SECONDARY IDE/HDD : None - ATA / None
FLOPPY : None - Floppy Disk / None
USB1 : USB - None / USB
USB2 : USB - None / USB
USB3 : USB - None / USB
USB4 : USB - None / USB
USB5 : USB - None / USB
USB6 : USB - None / USB
USB7 : USB - None / USB
USB8 : USB - None / USB
PS/2 Keyboard : Keyboard - None / PS/2
PS/2 Mouse : Mouse - None / PS/2
Parallel Port : Parallel Port ECP/EPP - None / DB-25 pin female
Serial Port 1 : Serial Port 16550 - None / DB-9 pin male
Serial Port 2 : Serial Port 16550 - None / DB-9 pin male
Joystick Port : Joystick - None / DB-15 pin female
MIDI Port : MIDI - None / DB-15 pin female
Line In Jack : Audio - None / Mini-jack
Lan : Network - None / RJ-45
Serial ATA1 : None - None / None
Serial ATA2 : None - None / None

Performance Tips
Notice 224 : SMBIOS/DMI information may be inaccurate.
Tip 2511 : Some memory slots are free so the memory can be easily upgraded.
Warning 100 : Large memory sizes should be made of Registered/Buffered memory.
Tip 2546 : Large memory modules should be ECC/Parity.
Tip 2548 : Speed set by software. For reliability, consider by jumpers/switch.
Tip 2 : Double-click tip or press Enter while a tip is selected for more information about the tip.
Warning 2518 : Mainboard temperature is too high.


Please help me out :(



Sponsored Link
Ads by Google

Response Number 1
Name: jam
Date: October 23, 2004 at 17:11:32 Pacific
Reply:

Did you have to post all that? All you had to say was your system temp is being reported as 57C, CPU as 43C...LOL!

Why are you using SANDRA to check your temps? It's highly unlikely that your board is hotter than your CPU. Either look in the BIOS or use Asus Probe. You should already have it, if not, go to the Asus website & download it...here's the link:

http://www.asus.com.tw/support/download/selectftp.aspx?l1_id=1&l2_id=11&l3_id=0&m_id=1&f_name=probe22301.zip~zaqwedc

Asus A7N8X-X
1800+ @8x210mhz
512mb PC3200
Ti4200/8X 128mb
WDC 60GB


0

Response Number 2
Name: OtheHill
Date: October 25, 2004 at 21:02:58 Pacific
Reply:

I agree with jam. The system temp and CPU temps are at the very least reversed.


0

Response Number 3
Name: Randy J. Anderson
Date: October 29, 2004 at 11:19:54 Pacific
Reply:

Warning, Sandra probably is wrong. For me, Sandra gotten my temperature readings wrong.

Sandra has a habit of displaying the wrong information for a good number of things :(.

Thus, in my opinion, Sandra is only good for benchmarking, ATM.


0

Sponsored Link
Ads by Google
Reply to Message Icon

Related Posts

See More







Post Locked

This post is quite old and has been locked from receiving new replies. Please create a new posting instead.


Go to CPUs/Overclocking Forum Home


Sponsored links

Ads by Google


Results for: Help System Board is to high temp

Is my cpu temp to high? www.computing.net/answers/cpus/is-my-cpu-temp-to-high/11713.html

HELP! 3dmark result is 8567 only!! www.computing.net/answers/cpus/help-3dmark-result-is-8567-only-/4450.html

voltage on tbird is too high www.computing.net/answers/cpus/voltage-on-tbird-is-too-high/4827.html